603

JUNCTION BOXES - SELECTIVE ENTRY Product Images 604 604W 603 603W 606 606W Brief Description of Products Features Junction box with cable entries in the side wall that are selectable by alignment of Captive cover fixing screw symbols and text on the cover. Slotted terminals allowing for unbroken ring wiring 4 Selective entries in side wall with knockouts allowing for apertures to be enlarged 4 knockouts in base Available in white and brown urea Technical Specifications (604, 604W products) Standard(s) BS EN 60670 Rating 30 Amp 250V~ Terminal Capacity - L & N 4 x 1.5mm No. of cable entries per terminal 1 No. of terminals 4 Covered by RoHS directive No No Covered by WEEE directive Size 80mm dia x 31mm Fixing Centres 50.8mm Technical Specifications (603, 603W products) Standard(s) BS EN 60670 Rating 20 Amp 250V~ Terminal Capacity - L & N 4 x 4.0mm No. of cable entries per terminal 1 No. of terminals 3 Covered by RoHS directive No No Covered by WEEE directive Size 89.5mm dia x 36mm Fixing Centres 50.8mm Technical Specifications (606, 606W products) Standard(s) BS EN 60670 Rating 20 Amp 250V~ Terminal Capacity - L & N 3 x 1.5mm No. of cable entries per terminal 1 No. of terminals 6 Covered by RoHS directive No No Covered by WEEE directive Size 88mm dia x 30mm Fixing Centres 50.8mm Line Diagrams 604 604W Packaging Information Packaging Type Pack Quantity Barcode Cat.No Description Product Inner Box Outer Box Each Inner Box Outer Box Individual Inner Box Outer Box 604 20A, 4 TERMINAL New BG Packing New BG Packing 10 100 5021166 603299 5021166 603282 10 100 5021166 603190 5021166 603183 604W 20A, 4 TERMINAL New BG Packing New BG Packing New BG Packing New BG Packing 603 10 100 5021166 604296 5021166 604289 30A, 3 TERMINAL 5021166 604197 5021166 604180 New BG Packing New BG Packing 10 100 603W 30A, 3 TERMINAL Clameshell 1 10 100 5021166606283 5021166606290 606 20 AMP, 6 TERMINAL 5021166606191 5021166606184 10 100 Clameshell 1 604W 20 AMP, 6 TERMINAL Weights and Dimensions Dimension ( W x L X H ) unit : cm Weight (g) CBM (m) Cat.No Description Product Inner Box Outer Box Each Inner Box Outer Box Individual Inner Box Outer Box 604 20A, 4 TERMINAL 604W 20A, 4 TERMINAL 603 30A, 3 TERMINAL 603W 30A, 3 TERMINAL 8.75 x 8.75 x 3.2 16.2 x 18.2 x 9.5 33.5x49.5x19.5 148 96 760 606 20 AMP, 6 TERMINAL 16.2 x 18.2 x 9.5 33.5x49.5x19.5 148 96 760 604W 20 AMP, 6 TERMINAL 8.75 x 8.75 x 3.2Installation Information Wire Identification Twin & Earth Cable WIRING Note - As from 1st April 2004 new colour codes for hard wire installations was introduced. INSTRUCTIONS EARTH = GREEN/YELLOW Sleeving BLACK (pre Apr 04) / BLUE (after Apr 04) = NEUTRAL RED (pre Apr 04) / BROWN (after Apr 04) = LIVE JUNCTION BOXES The ends of the individual conductors should have the insulation removed TECHNICAL HELPLINE: 0800 169 5560 by approx. 10mm. Any bare earth conductors should be sleeved to within 10mm of the ends. (These details are for general information only and SAFETY WARNING conductor lengths may need to be trimmed in certain installations). Before use please read carefully and use in accordance with these safety For lighting circuits, use sleeving of the appropriate live colour to ensure wiring instructions. clear identification of live connections. Before commencing any electrical work ensure the supply is switched off See diagram for typical lighting circuit wiring using 4-way junction box. at the mains, either by switching off the consumer unit or by removing the appropriate fuse. To prevent fire hazard always use cable of the correct rating and type. Wiring should be in accordance with the latest edition of the IEE regulations (BS 7671). If in doubt consult a competent electrician. 1. 4-WAY JUNCTION BOX FOR LIGHTING CIRCUIT JUNCTION BOX GENERAL ADVICE The terminals of Junction Boxes can be used for any polarity. Remove the central screw and remove cover to expose terminals. In multi-terminal junction boxes, take care to use only one polarity in any one group of terminals. Position the way the cable lies, so as to pass through one of the apertures in the side of the base. For Selective Entry boxes selecting the apertures to be used by rotating the guide marked on the lid. When cable installations are complete, position the cover so as to block off the cable entry apertures not used in the base and tighten the screw. Alternatively for non-selective junction boxes the required apertures can be easily broken away using apair of pliers and with minimal force. Clean edges to remove any sharp edges. 2. 3.