www.iso-tip.com How To Use QUICK CHARGE info iso-tip.com Operation 1.1 Turn button to use position. Tel: (715) 831-6353 1.2 Depress button to operate. Fax: (419) 818-0897 1.3 When not in use, turn button to lock position 704 Bartlett Avenue Altoona, WI 54720 USA Soldering on Printed Circuit Boards, Wiring and General Work Make sure work is clean and make a good mechanical connection where possible. Flux the joint, if necessary. Remove QUICK CHARGE from its recharging stand, depress push button, wait 3-5 seconds and apply tip to The QUICK CHARGE 7740 joint that is to be soldered. Up to 125 solder joints per charge Immediately apply solder at the point of the tip and the joint so that melted solder will help in heat transfer. When solder flows and has wetted connection, remove solder and soldering iron and release push button. Fully recharges in 3-1/2 to 4 hours Soldering cycle should be completed within 15 seconds. Unnecessary usage will reduce joint capacity as will too large of work. READ ALL INSTRUCTIONS BEFORE Check your work a good solder joint should look smooth and bright. USING. When using your QUICK CHARGE, After connection has cooled, trim off excess wire. basic precautions should always be Installing Tip followed. 2.1 Align tip leads over the terminal holes. 2.2 Push inward and upward until tip is full seated. Danger. 2.3 To remove, pull straight out. When the QUICK CHARGE operating 2.4 To attach the tip permanently, remove the two terminal screws and take off the two springs. Then insert button is pressed, the tip heats up over the tip into the tip holders. Replace the screws and tighten. 900F, almost immediately. Replacing the Batteries Warning: In the unlikely event that you have to replace the soldering irons Ni-Cad batteries: 3.1 Remove three screws from case. Remove cover carefully. DO NOT hold the tip when pushing the 3.2 Remove switch contact screw. Lift switch spring and tip holder assembly up and remove from unit. button. 3.3 Remove 2 screws located on ends of battery pack. Whenever you are finished soldering, 3.4 Remove battery pack. make sure to rotate button back to lock 3.5 Install new battery pack with 2 screws. position. 3.6 Replace switch spring and tip assembly in case. Use caution Do not touch the other tip assembly. DO NOT allow metal objects to touch 3.7 Replace switch contact screw. or short across the recessed charging 3.8 Replace cover and 3 screws. contact points. The metal could get very hot. Recharging The recharging stand is designed to be operated on 100 to 120 Volts, 50-60 Cycle. DO NOT lay against any surface after To recharge, place QUICK CHARGE in the recharging stand with the push button toward the front. using until the TIP HAS COOLED. To recharge using the wall plug transformer, plug charger cord into bottom of iron and plug charger only into a 120 Volt AC, 50/60 Cycle receptacle. General Soldering Information Recharge from DEAD to FULL CHARGE (recharging stand) 7700, 7740, 7904, 7944, Quick Charge For fast and accurate soldering, a clean and and Power Pro units in 3-4 1/2 hours. well-tinned tip is required. Using the wall plug transformer charging time is 12-16 hours and can be used with all models except for Heat and gently wipe with a rag or an 7800, 7840. emery cloth to clean tip. It is suggested to charge iron when received and to leave in recharging stand or plugged into wall plug Re-tin to minimize oxidation. transformer when not in use. Soldering iron will not overcharge. Use good quality solder. The recharging stand for the 7944 and 7904 has a LED to indicate charging status. RED indicates that the Use Resin Core or solid with the proper flux iron is not charging YELLOW/GREEN indicates that the iron is charging. If the RED light appears when for electronics work. you place the iron in the stand, always check to see that the stand is connected to a power source. Apply solder ONLY at the point of the tip. Replacement Tips Regular Tips High Efficiency Tips Recommended Practices and Answers to Frequently Asked Questions: You CAN leave your QUICK CHARGE in its charging stand all of the No. 7571 Beveled Tip No. 7574 Concave Centering Tip No. 7535-100 HI-E Regular Tip time when not in use - it will NEVER overcharge. To save electricity, 1/16 (1.6mm) 5/32 (4mm) 5/32 (4mm) the charger can be unplugged if long periods of non-use are expected. If the soldering iron is left in the stand and the recharging stand is disconnected or turned off, the iron will discharge. No. 7579 Beveled Tip 3/32 (2.4mm) No. 7545-100 HI-E Fine Tip No. 7573 Tinning Tip The iron should be used frequently to insure a longer life of its 1/16 (1.6mm) 5/32 (4mm) batteries. Even when you dont solder, it is a good practice to completely discharge the batteries by normal use at least once a No. 7592 Beveled Tip month. If this is not done, the batteries will gradually lose their 5/32 (4mm) No. 7569 V Tip 5/32 (4mm) No. 7546-100 HI-E Heavy Duty Tip maximum capacity. However, when discharging, DO NOT hold the High Wattage 3/16 (4.8mm) iron continuously in the ON position without a HEAT SINK to prevent No. 7593 Beveled Tip abnormally high tip temperature. High Wattage 3/16 (4.8mm) No. 7572 Blunt Tip 5/32 (4mm) NEVER charge your QUICK CHARGE soldering iron in a RECHARGER No. 7566-100 HI-E Micro Soldering Tip stand that is a different color than the iron. The higher charge rate of 1/16 (.4mm) different colored stands may cause overcharging and overheating of No. 7566 Micro Soldering Tip No. 7577 Chisel Tip 1/64 (.4mm) the irons rechargeable cells, and this will shorten battery life. 5/32 (4mm) When soldering, touch only the nose of the tip to the area you are No. 7577-100 HI-E Chisel Tip soldering and not the thin sidewalls. Do not feed the solder onto the 5/32 (4mm) side of the tip. This practice will rapidly eat a hole through the side No. 7535 Regular Tip No. 7545 Fine Tip 5/32 (4mm) 1/16 (1.6mm) of the copper tip. Feed the solder onto the very end of the tip at the junction with the work. No. 7546-100 HI-E Beveled Tip 3/32 (2.4mm) All tips should be kept tinned for fast heat transfer to the work and No. 7546 Heavy Duty Tip No. 7596 Knife Tip longest tip life. (See directions under General Soldering Information.) High Wattage 3/16 (4.8mm) 1/32 (.8mm) Tip temperature can be controlled by pressing the button momentarily off and on in use. This may be necessary when working with micro printed circuits. No. 7541 Circuit Breaker Tip Warranty Please contact us via phone or e-mail for specific product warranties or any other questions you may have. X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Soldering Irons category: Click to view products by Iso-Tip manufacturer: Other Similar products are found below : 0052918099 0058759725 918100-TE PTTC-802 SFV-DRK30AR SMTC-0167 SMTC-1121 SMTC-1169-PK SMTC-8170 AC-CK1 AC- CK2 SSC-625A SSC-626A SSC-638A SSC-726A FG-BVX STTC-042 STTC-114 STTC-838P STV-CH24A SCP-CH25 SFP-DRH05 SMTC-101 SMTC-160-PK SMTC-1BL250 SSC-645A SSC-671A SSC-672A SSC-742A SSC-745A SSC-746A SSC-770A SSC-772A STDC-804 STTC-105 STTC-120 STTC-547 1-91362-0 T0054487399 T0054472199 T0054465699 STTC-820 SMTC-004 MX-H1GKG SCV-CH30AR T0054440699 PTTC-801B STTC-845P SCV-CH24A PHT-754487F