ALUMINUM ELECTROLYTIC CAPACITORS Miniature Sized, Low lmpedance, High Reliability For Switching Power Supplies PW series Smaller case size and lower impedance than PM series. Low impedance and high reliability withstanding 2000 hours to 8000 hours. Capacitance ranges available based on the numerical values in E12 series under JIS. PM Compliant to the RoHS directive (2011/65/EU). Smaller Low Long Life PA TT Impedance PW Specifications Item Performance Characteristics Category Temperature Range 55 to +105C (6.3 to 100V), 40 to + 105C (160 to 400V), 25 to +105C (450V) Rated Voltage Range 6.3 to 450V Rated Capacitance Range 0.47 to 15000F Capacitance Tolerance 20% at 120Hz, 20C Rated voltage (V) 6.3 to 100 160 to 450 < Leakage Current After 1 minute s application of rated voltage at 20C, leakage current CV 1000 : I = 0.1CV+40 (A) max. = Leakage current is not more than 0.03CV or 4 (A), whichever is greater. CV > 1000 : I = 0.04CV+100 (A) max. For capacitance of more than 1000 F, add 0.02 for every increase of 1000 F. Measurement frequency : 120Hz at 20C Rated voltage (V) 6.3 10 16 25 35 50 63 100 160 to 250 315 350 400 450 Tangent of loss angle (tan ) tan (MAX.) 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08 0.15 0.20 0.25 120Hz Rated voltage (V) 6.3 10 16 25 35 50 63 100 160 200 250 315 350 400 450 Z 25C / Z+20C 3 4 Stability at Low Temperature 3 6 15 Impedance ratio Z40C / Z+20C 4 6 8 10 (MAX.) Z55C / Z+20C 3 3 3 3 The specifications listed at right shall be met when the Capacitance change capacitors are restored to 20C after D.C. bias plus rated Within 20% of the initial capacitance value Endurance ripple current is applied for 8000 hours (2000 hours for D=4, tan 200% or less than the initial specified value 5 and 6.3, 3000 hours for D=8, 5000 hours for D=10, 7000 Leakage current Less than or equal to the initial specified value hours for D=12.5) at 105C, the peak voltage shall not exceed the rated voltage. After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Marking Printed with white color letter on dark brown sleeve. Radial Lead Type Type numbering system (Example : 10V 680F) Sleeve (P.E.T.) d 1 2 3 4 5 6 7 8 9 10 11 12 U P W 1 A 6 8 1 M P D Size code Configuration Capacitance tolerance (20%) MIN MIN + MAX. 15 4 Rated capacitance (680F) L Rated voltage (10V) Pressure relief vent 6.3up (No pressure relief vent for 7mmL products) Series name Type (mm) Configuration (L = 7) 1.0 4 5 6.3 8 10 12.5 16 18 20 22 25 D Pb-free leadwire D (L < 20) 1.5 P 1.5 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0 10.0 12.5 Pb-free PET sleeve (L 20) 2.0 0.45 0.5 0.5 0.6 0.6 0.6 0.8 0.8 1.0 1.0 1.0 4 5 DD d (0.45) (0.45) 0.8 6.3 ED (7mm L : DD) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.0 8 10 PD : Applied to L>25 products 12.5 to 18 HD ( ): Applied to 7mmL products 20 to 25 RD Please refer to page 20 about the end seal configuration. Frequency coefficient of rated ripple current Frequency V Cap. (F) 50Hz 120Hz 300Hz 1kHz 10kHz or more 0.47 to 56000 0.20 0.30 0.50 0.80 1.00 68 to 330. 0.55 0.65 0.75 0.85 1.00 6.3 to 100 390 to 1000. 0.70 0.75 0.80 0.90 1.00 .1200 to 150000 0.80 0.85 0.90 0.95 1.00 0.47 to 22000 0.80 1.00 1.25 1.40 1.60 160 to 450 330 to 4700. 0.90 1.00 1.10 1.13 1.15 Please refer to page 20, 21, 22 about the formed or taped product spec. Please refer to page 4 for the minimum order quantity. CAT.8100D Dimension table in next page. + MAX. D 0.5 PALUMINUM ELECTROLYTIC CAPACITORS PW series Standard Ratings V (Code) 6.3 (0J) 10 (1A) Case size Rated ripple Case size Rated ripple Impedance () MAX. Impedance () MAX. Item (mArms) (mArms) D L D L Cap.(F) 20C / 100kHz 10C / 100kHz 20C / 100kHz 10C / 100kHz (mm) 105C / 100kHz (mm) 105C / 100kHz Code 5 11 0.60 1.20 180 22 220 5 11 0.60 1.20 180 4 7 2.00 5.00 65 27 270 4 7 2.00 5.00 65 5 11 0.60 1.20 180 5 11 0.60 1.20 180 33 330 5 7 5 7 0.95 2.40 120 0.95 2.40 120 39 5 7 390 0.95 2.40 120 5 11 5 11 0.60 1.20 180 0.60 1.20 180 47 470 5 7 0.95 2.40 120 4 11 1.30 2.60 120 56 560 5 7 0.95 2.40 120 68 680 4 11 1.30 2.60 120 5 11 0.60 1.20 180 82 820 6.3 7 0.45 1.20 200 5 11 0.60 1.20 180 100 101 5 11 0.60 1.20 180 5 15 0.50 1.00 235 120 121 6.3 7 0.45 1.20 200 6.3 11 0.25 0.50 290 150 151 6.3 11 0.25 0.50 290 5 15 0.50 1.00 235 180 6.3 11 181 0.25 0.50 290 6.3 11 0.25 0.50 290 220 6.3 11 221 0.25 0.50 290 6.3 15 0.23 0.46 430 6.3 11 0.25 0.50 290 330 331 8 11.5 0.117 0.234 555 6.3 15 0.23 0.46 430 470 471 8 11.5 0.117 0.234 555 8 11.5 0.117 0.234 555 560 561 8 11.5 0.117 0.234 555 10 12.5 0.090 0.180 760 680 681 10 12.5 0.090 0.180 755 8 15 0.085 0.170 730 8 15 0.085 0.170 730 820 821 10 12.5 0.090 0.180 755 10 16 0.068 0.136 1050 1000 102 10 12.5 0.090 0.180 755 8 20 0.065 0.130 995 8 20 0.065 0.130 995 1200 10 20 122 0.052 0.104 1220 10 16 0.068 0.136 1050 10 20 0.052 0.104 1220 1500 152 10 20 0.052 0.104 1220 10 25 0.045 0.090 1440 12.5 20 0.038 0.076 1655 12.5 20 0.038 0.076 1655 2200 222 10 25 0.045 0.090 1440 10 31.5 0.035 0.070 1815 2700 272 10 31.5 0.035 0.070 1815 12.5 25 0.030 0.060 1945 12.5 25 0.030 0.060 1950 3300 332 12.5 20 0.038 0.076 1655 12.5 31.5 0.025 0.050 2310 12.5 35.5 0.022 0.044 2510 3900 392 12.5 25 0.030 0.060 1945 16 20 0.029 0.058 2210 16 25 0.022 0.044 2555 4700 16 25 472 0.022 0.044 2555 12.5 31.5 0.025 0.050 2310 12.5 35.5 16 25 0.022 0.044 2510 0.022 0.044 2560 5600 562 16 20 18 20 0.029 0.058 2210 0.028 0.056 2490 16 25 0.022 0.044 2560 16 31.5 0.018 0.036 3010 6800 682 18 20 0.028 0.056 2490 18 25 0.020 0.040 2740 16 35.5 0.016 0.032 3150 8200 822 16 31.5 0.018 0.036 3010 18 31.5 0.016 0.032 3635 16 31.5 0.016 0.032 3150 10000 103 18 35.5 0.015 0.030 3680 18 25 0.020 0.040 2740 12000 123 18 31.5 0.016 0.032 3635 15000 153 18 35.5 0.015 0.030 3680 18 40 0.014 0.028 3800 : In this case, 6 will be put at 12th digit of type numbering system. CAT.8100D