DRA1-SPFE240A25 Sensata

DIN Rail Mount DataSheet DRA1 SPF Series 10mm Single Channel DIN Rail Mount SSR Assembly AC Ratings up to 380 VAC and 10 Amps 3-15 VDC, 15-32VDC, 18-36 VAC and 90-140 VAC Control Cage style screw terminals for easy connection Fits standard 35mm DIN rail Includes LED Status indicator (DC control only) PRODUCT SELECTION Control Voltage 10 A (Zero Voltage Turn-on) 10 A (Instantaneous Turn-on) DRA1-SPF240D25R 3-15 VDC DRA1-SPF240D25 4-15 VDC DRA1-SPF380D25 DRA1-SPF380D25R 15-32 VDC DRA1-SPFE240D25 DRA1-SPFE240D25R 18-36 VAC DRA1-SPFE240A25 90-140 VAC DRA1-SPF240A25 (1) OUTPUT SPECIFICATIONS SPF(E)240x25 SPF380x25 Description Operating Voltage VAC 12-280 48-380** Transient Overvoltage Vpk 600 1200 Maximum Load Current Arms (2)(3) 10 10 Minimum Load Current Arms 0.06 0.06 Maximum Off-State Leakage Current Rated Voltage mArms 0.1 0.1 Minimum Off-State dv/dt maximum rated voltage V/sec (4) 500 500 Maximum 1 Cycle Surge Current (50/60 Hz) Apk 239/250 239/250 Maximum I t for Fusing (50/60 hz, 1/2 cycle) A sec 285/260 285/260 Maximum On-State Voltage Drop Rated Current Vpk 1.6 1.6 (1) INPUT SPECIFICATIONS Description SPF240D25 SPF380D/480D SPFE240D25 SPF240A25 SPFE240A25 Control Voltage Range 3-15 VDC 4-15 VDC 15-32 VDC 90-140 Vrms 18-36 VAC Minimum Turn-On Voltage 3.0 VDC 4.0 VDC 15 VDC 90 Vrms 18 Vrms Must Turn-Off Voltage 1.0 VDC 1.0 VDC 1.0 VDC 10 Vrms 2 Vrms Typical Input Current 15 mA 15 mA 15 mA 10 mArms 10 mArms Nominal Input Impedance 300 Ohm 240 Ohm 1500 Ohm 14.1 k Ohm 2.1 k Ohm Maximum Turn-On Time msec (5) 1/2 Cycle 1/2 Cycle 1/2 Cycle 10 10 Maximum Turn-Off Time sec 1/2 Cycle 1/2 Cycle 1/2 Cycle 40 40 (1) GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output (50/60Hz) 4000 Vrms 9 Minimum Insulation Resistance ( 500 VDC) 10 Ohms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -30 to 80 C Ambient Storage Temperature Range -30 to 125 C Weight (typical) 0.32 lb oz (145.5 g) Encapsulation Thermally conductive Epoxy GENERAL NOTES (1) All parameters at 25C unless otherwise specied. (2) See derating chart on page 3. (3) Steady state load current exceeding 10 Amps will damage socket. (4 Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (5) Turn-On Time for DC control instantaneous turn-on versions is 0.1 msec. ** NOTE: Voltages in excess of 380V will damage output terminals. Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.DIN Rail Mount DataSheet (A) WIRING DIAGRAM 0.20 0.40 INPUT OUTPUT 5.1 10.2 0.50 4 2 12.7 (B) Load Control (C) 4 3 2 1 Power 3 + 1 (A) Wiring diagram is identical for each individual section whether it is a single or four channel assembly. (B) Load can be placed on either side of Power. (C) LED and Resistor not installed for AC input. MECHANICAL SPECIFICATIONS Tolerances: 0.02 in / 0.5 mm All dimensions are in: inches millimeters 0.9 22.9 2.75 69.9 1.71 2.06 43.3 52.3 1.48 37.7 0.39 3.53 10.0 89.6 Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.