PSD4810

Panel Mount Datasheet PS48 Series Peak-fire SSR for high inductance applications Ratings from 10A to 90A 380-530 VAC SCR output for heavy industrial loads DC Control PRODUCT SELECTION Control Voltage 10A 25A 50A 90A 4-32 VDC PSD4810 PSD4825 PSD4850 PSD4890 AVAILABLE OPTIONS Load Current 10: 10 Amps Status indicator 25: 25 Amps Blank: No Input Status LED Control Voltage 50: 50 Amps Series G: Input Status LED D: 4-32 VDC 90: 90 Amps PS D 48 10 F G Operating Voltage Termination 48: 380-530 VAC Blank: No Faston Terminals F: Faston Terminals Required for valid part number For options only and not required for valid part number Not all part number combinations are available. * Contact Crydom Technical Support for information on the availability of a specific part number. (1) OUTPUT SPECIFICATIONS 10A 25A 50A 90A Description 380-530 380-530 380-530 380-530 Operating Voltage (47-63Hz) Vrms 1200 1200 1200 1200 Transient Overvoltage Vpk 10 10 10 10 Maximum Off-State Leakage Current Rated Voltage mArms 500 500 500 500 Minimum Off-State dv/dt Maximum Rated Voltage V/sec (2) 10 25 50 90 Maximum Load Current Arms (3) 40 40 40 40 Minimum Load Current mArms 134/140 239/250 597/625 1145/1200 Maximum 1 Surge Current (50/60Hz) Apk 1.6 1.6 1.6 1.6 Maximum On-State Voltage Drop Rated Current Vpk 1.48 1.02 0.63 0.28 Thermal Resistance Junction to Case (Rjc) C/W 89/81 285/259 1779/1621 6560/5976 Maximum 1/2 Cycle I t for Fusing (50/60Hz) A sec 0.5 0.5 0.5 0.5 Minimum Power Factor (at Maximum Load) (1) INPUT SPECIFICATIONS Description DC Control Control Voltage Range 4-32 VDC Maximum Turn-On Voltage (2) 4.0 VDC Minimum Turn-Off Voltage 1.0 VDC Maximum Reverse Voltage -32 Typical Input Current (4) 8 mADC Nominal Input Impedance See note (4) Maximum Turn-On Time msec 1/2 Cycle Maximum Turn-Off Time msec 1/2 Cycle Do not forget to visit us at: www.crydom.com Copyright 2016 Crydom Inc. Specifications subject to change without notice.Panel Mount Datasheet (1) GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) 4000 Vrms 9 Minimum Insulation Resistance ( 500 VDC) 10 Ohm Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40 to 80 C Ambient Storage Temperature Range -40 to 125 C Weight (typical) 3.0 oz (86.5g) Encapsulation Thermally conductive Epoxy Terminals Screw and Saddle Clamps Furnished, Unmounted Recommended Terminal Screw Torque Range: 6-32 Screws - 10 in/lbs. 8-32 & 10-32 Screws - 20 in/lbs. Faston Single pair (up to 25A) Double pair*(50A model only) *Caution: User must connect to both pairs GENERAL NOTES (1) All parameters at 25C unless otherwise specied. (2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (3) Heat sinking required, for derating curves see page 3. (4) Input circuit incorporates active current limiter. MECHANICAL SPECIFICATIONS 1.10 (27.9) MOUNTING HOLE/SLOT .45 M 4 TERMINAL 0.192 (4.9) DIA. (11.4) (2 PLACES ) OUTPUT 2.30 12 (58.4) 1.87 1.70 (47.5) (43.2) -- + 4 3 INPUT 1.00 .78 BASE PLATE (25.4) M 3 TERMINAL (19.8) .125 (3.2) (2 PLACES) 1.80 .9 (45.7) (23.0) FASTON TERMINAL 1.10 .250 X .032 (2 PLCS.) (27.9) MOUNTING .87 REF. HOLE/SLOT .45 (22.2) 0.192 (4.9) DIA. (11.4) OUTPUT 2.30 12 (58.4) 1.87 1.70 (47.5) (43.2) -- + 4 3 INPUT 1.00 .78 BASE PLATE (25.4) FASTON (19.8) .125 (3.2) TERMINAL 1.80 .900 (45.7) .187 X .032 (23.0) (2 PLCS.) Do not forget to visit us at: www.crydom.com Copyright 2016 Crydom Inc. Specifications subject to change without notice.