EETED2G101BA

10.00.1 (10.0) Aluminum Electrolytic Capacitors/ ED Snap-in Type Series: Type: ED TS Features Endurance : 105 C 3000 h High ripple current capability in high frequency range. RoHS directive compliant Speci cations Category Temp. Range 40 C to + 105 C 25 C to +105 C Rated W.V. Range 200 V.DC to 250 V.DC 400 V.DC to 450 V.DC Nominal Cap. Range 220 F to 2200 F 56 F to 560 F Capacitance Tolerance 20 % (120 Hz/+20 C) 3 CV (A) max. After 5 minutes application of rated working voltage at +20 C DC Leakage Current C : Capacitance (F) V: W.V. (V.DC) tan Please see the attached standard products list After 3000 hours application of DC voltage with speci ed ripple current (< rated DC working voltage) at +105 C2 C, the capacitors shall meet the following limits. Endurance Capacitance change 20 % of initial measured value < tan < 200 % of initial specied v alue DC leakage current < initial specied v alue After storage for 1000 hours at +105 C2 C within no voltage applied and then being stabilized Shelf Life at +20 C, capacitors shall meet the limits speci ed in Endurance (With voltage treatment) Frequency correction factor for ripple current Frequency (Hz) 50 60 100 120 5001 k 10 k to Correction factor 0.50 0.55 0.68 0.70 0.85 0.90 1.00 Di men sions in mm (not to scale) (Unit : mm) 2-2.00.1 Sleeve Polarity bar Vent L+2.0 max. (D) 4.00.5 Rated voltage etc. indicate to sleeve. Recommended PWB piercing plan +0.2 2.0 max. Terminal 0.8 0.1 (t=0.8) 1.50.2 Top of spin Standard terminal type does not require terminal trimming process. Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Nov. 2012 EEE-131 D+1.0 max. (3.5) 4.00.5Aluminum Electrolytic Capacitors/ ED Standard Prod ucts Endurance : 105 C 3000 h Case size Part No. Speci cation Min. Packaging Q ty PET sleeve Ripple tan W.V. Cap. Terminal Length Current (120 Hz) Dia. Length (120 Hz) 4.0 mm (50 kHz) (+20 C) (20 %) (Without Top Plate) (+105 C) max. (V. DC) (F) (mm) (mm) (A r.m.s.) (pcs) 270 22 25 EETED2D271HJ 2.03 0.15 200 330 22 30 EETED2D331HJ 2.23 0.15 200 22 30 EETED2D391HJ 2.44 0.15 200 390 25 25 EETED2D391JJ 2.44 0.15 200 22 35 EETED2D471HJ 2.64 0.15 200 470 25 30 EETED2D471JJ 2.64 0.15 200 22 40 EETED2D561HJ 3.05 0.15 200 560 25 30 EETED2D561JJ 3.05 0.15 200 30 25 EETED2D561KJ 3.05 0.15 200 22 45 EETED2D681HJ 3.45 0.15 200 680 25 35 EETED2D681JJ 3.45 0.15 200 30 30 EETED2D681KJ 3.45 0.15 200 200 22 50 EETED2D821HJ 3.76 0.15 200 25 40 EETED2D821JJ 3.76 0.15 200 820 30 30 EETED2D821KJ 3.76 0.15 200 35 25 EETED2D821LJ 3.76 0.15 200 25 45 EETED2D102JJ 4.06 0.15 200 1000 30 35 EETED2D102KJ 4.06 0.15 100 35 30 EETED2D102LJ 4.06 0.15 200 30 40 EETED2D122KJ 4.47 0.15 100 1200 35 35 EETED2D122LJ 4.47 0.15 100 30 50 EETED2D152KJ 5.08 0.15 100 1500 35 40 EETED2D152LJ 5.08 0.15 100 1800 35 45 EETED2D182LJ 5.48 0.15 100 2200 35 50 EETED2D222LJ 5.89 0.15 100 270 22 30 EETED2Q271HJ 2.03 0.15 200 22 30 EETED2Q331HJ 2.23 0.15 200 330 25 25 EETED2Q331JJ 2.23 0.15 200 22 35 EETED2Q391HJ 2.44 0.15 200 390 25 30 EETED2Q391JJ 2.44 0.15 200 22 40 EETED2Q471HJ 2.64 0.15 200 470 25 30 EETED2Q471JJ 2.64 0.15 200 30 25 EETED2Q471KJ 2.64 0.15 200 22 45 EETED2Q561HJ 3.05 0.15 200 560 25 35 EETED2Q561JJ 3.05 0.15 200 30 30 EETED2Q561KJ 3.05 0.15 200 220 25 40 EETED2Q681JJ 3.45 0.15 200 680 30 30 EETED2Q681KJ 3.45 0.15 200 35 25 EETED2Q681LJ 3.45 0.15 200 25 45 EETED2Q821JJ 3.76 0.15 200 820 30 35 EETED2Q821KJ 3.76 0.15 100 35 30 EETED2Q821LJ 3.76 0.15 200 30 40 EETED2Q102KJ 4.06 0.15 100 1000 35 35 EETED2Q102LJ 4.06 0.15 100 30 45 EETED2Q122KJ 4.47 0.15 100 1200 35 40 EETED2Q122LJ 4.47 0.15 100 1500 35 45 EETED2Q152LJ 5.08 0.15 100 1800 35 50 EETED2Q182LJ 5.48 0.15 100 When capacitors of 35 45L and 35 50L are mount ed on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives in clud ing halogenated compositions.) Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Nov. 2012 EEE-132