Cleaning: > Clean this light fitting only with a soft dry cloth > Do not use any chemical or abrasive cleaners. Lamp replacement: Battery replacement: If after routine operation check, the lamp does not remain > Switch off the electricity at the mains. lit for the three hour period, new batteries may be > Remove two screws on the front of the light and lift required. off the diffuser. 1) Switch off the electricity at the mains. > Remove the bayonet lamp. 2) Allow batteries to fully discharge then reconnect to supply and allow to charge for 24 hours. > Insert new lamp. 3) Test again for 3 hours, if light does not remain lit > Replace diffuser. change the battery pack as follows: > Restore the power and perform operation check. 4) Remove the two screws on each side of the front Non-maintained emergency light panel and lift off. 5) Unplug the battery leads from the batteries. 6) Lift the batteries out of the case. Replacement lamp type: 220W 7) Write current date on the new batteries. 8) Fit new batteries into the case. Type: 12V 20 W 9) Reconnect the battery leads. BA 15s Model(s) 10) Close and secure the front cover. TWINSPOTNM 11) Restore power and allow to charge for 24 hours. Replacement battery type: 12) Perform full operation check and update test record. 12V 7Ah Lead / Acid Specification: Eventually, you may want to replace this light fitting: When your light fitting and or battery pack come to the end of their life or you choose to update Power 2 20W or upgrade the fitting by replacing it, please do not dispose of it with your normal household waste, please recycle where facilities exist. When you need to dispose of this fitting, check with Continuous illumination >3 hours your retailer or local authority for suitable options. New regulations will encourage the recycling of Waste from Electrical and Electronic Equipment ( European WEEE Directive effective Battery 12V 7Ah August 2005 ). Recharge time ~24 hours Over-discharge protection Yes If you experience problems: If your light is defective or develops a fault, please return it to the place where you bought it. You can call our Helpline for advice. The Helpline will gladly give advice on any aspect of any Eterna Lighting product but may not be able to give specific instructions regarding individual installations. If in doubt, consult a qualified electrician. PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING YOUR NEW FITTING Help line: - - Tel: 01933 673 144 Fax: 01933 678 083 Email: sales eterna-lighting.co.uk PLEASE RETAIN FOR FUTURE REFERENCE For answers to frequently asked questions ( FAQs ) and other information visit our web-site www.eterna-lighting.co.uk Each month: Important notes: Read this first: Installation: Please keep this instruction booklet and test record in a safe Isolate the power supply and check the light is illuminated. 1) Undo the screws on each side of the front panel and > This light fitting must be installed in accordance place. A fire officer or other authorised person may want to see This test should last for no more than 45 minutes. lift off. with the Building Regulations making reference your record of inspection and testing. Endorse the test record form supplied. 2) Disconnect and remove the batteries noting the to the Wiring Regulations BS7671. The Building connections. The ballast and control gear must be operated only within the Regulations may be obtained from HMSO or viewed 3) Choose which side of the fitting you need to make enclosure supplied. The gear must not be operated outside of the Every six months: and downloaded from www.communities.gov.uk enclosure. your cable entry and knock out the slug. following the link for Building Regulations. The battery charging circuit and control gear are separated from 4) Using the back of the fitting as a template, mark the Isolate the power supply and check that the light is still > Switch off the mains before commencing installation the mains by SELV. position of the fixing holes on your mounting surface. illuminated after 1 hour. Endorse the test record form. and remove the appropriate circuit fuse. 5) Make fixing holes and fit plugs as appropriate. When energised by a constant mains supply, the battery will be > Your emergency fittings should have their own 6) Secure the back of the fitting to the mounting surface constantly charged. On failure of the constant mains supply, the Once each year: separate mains supply circuit and should not share using suitable fixings ( not supplied ). fitting will switch automatically by relay from battery charging to their supply with other lighting or electrical devices. 7) Fit a cable gland ( not supplied ) into the cable entry battery discharge powering the lamps. Both the mains and battery Isolate the power supply and check that the light is still supplies incorporate fuse protection: see fitting for location and hole. > This product is suitable for installation on flammable illuminated after 3 hours. Endorse the test record form. rating. 8) Thread the supply cable through the gland and into surfaces ( indicated by the in a triangle ) the fitting. > Suitable for indoor use only. 9) Make connection to the mains supply according to > Before making fixing hole(s), check that there are no the colour code opposite. Take care not to leave any obstructions hidden beneath the mounting surface strands protruding from the terminals and to tighten such as pipes or cables. all terminals securely. Ensure also that the terminals clamp onto the bare wire and not onto the insulation. > The chosen location of your new fitting should allow 10) Write the current date on the battery pack. for the product to be securely mounted and safely 11) Replace the batteries and reconnect. Ensure that the connected to the mains supply. batteries are connected with correct polarity, i.e.: Red > Ensure that the fitting will be accessible after +, Black . installation for maintenance. 12) Fit the battery fuse into the fuse holder on the PCB. > If the location of your new fitting requires the Fuses are supplied in a small plastic bag fixed to the provision of a new electrical supply, the supply must battery lead. conform with the requirements of the Building 13) Replace the front cover and secure with the two Regulations making reference to the Wiring remaining screws. Regulations ( see above ). 14) Restore the power supply. > Make connections to the electrical supply in 15) Check that the Green LEDs that indicate charging accordance with the following code: and continuity in the two lamps are all lit. Live - L Neutral - N Earth - E > This product must be connected to Earth. Operation checks: Periodic testing should be carried out monthly by > You are advised at every stage of your installation to simulating a failure of supply, causing the fitting to be double-check any electrical connections you have energised from its battery. Interruption of the supply made. After you have completed your installation should be carried out by the operation of a local keyswitch there are electrical tests that should be carried out: or other isolation device. During this period all fittings these tests are specified in the Wiring Regulations should be examined visually to ensure that they are ( BS7671 ) referred to in the Building Regulations. If functioning correctly. At the end of the test period the in doubt, consult a qualified electrician. supply shall be restored and all indicator lamps or devices checked to ensure that the normal supply has been restored. The duration of the simulated failure shall be as follows:- contd Safety markings: TWINSPOTNM Non-maintained emergency bulkhead light 070809PA