Ships to you between Fri. 17 May to Thu. 23 May
0011030043 HT60923A Molex
Crimpers / Crimping Tools 60703-3 COVER PLATE Stock : 2
Molex 60703-5 FRONT COVER PLATE Stock : 2
Crimpers / Crimping Tools CRIMPER, INS F (.070 ) Stock : 3
Crimpers / Crimping Tools CRIMP INSULATION "O" Stock : 0
Crimpers / Crimping Tools CRIMPER INSUL O Stock : 9
Bench Top Tools CRIMPER WIRE .062 F Stock : 0
Crimpers ANVIL Stock : 0
Bench Top Tools CRIMPER INSULATION F (.070 ) Stock : 0
Crimpers / Crimping Tools AA-400-138-BODY- REPL-KIT Stock : 2
Wire Labels & Markers HT-SCE-1/2-2.0-4 Stock : 6750
Crimpers / Crimping Tools ANVIL Stock : 4
APPLICATION NEEDLE, 0.1MM Stock : 0
HT60923A Extractor Tool Extractor Tool Instruction Sheet Order No. 11-03-0043 Engineering No. HT60923A FEATURES This tool is designed to extract many different terminal series from various plug and receptacle housings. See Chart below. SCOPE Products: Terminal Housings Description Terminal Order No. Series No. Series No. 43030-0001 43030-0002 43030-0003 43030-0004 43030-0005 43025 43030-0006 43030-0007 43030-0008 43030-0009 43030-0010 43030 43645 43030-0011 43030-0012 43030-0051 43030-0052 43030-0053 44133 43030-0056 43030-0057 43030-0058 43030-0059 43030-0080 Micro-Fit 3.0 43030-0081 43030-1001 Crimp Terminal 43031-0001 43031-0002 43031-0003 43031-0004 43031-0005 20-24 AWG 43020 43031-0006 43031-0007 43031-0008 43031-0009 43031-0010 43031 43640 43031-0011 43031-0012 43031-0016 43031-0017 43031-0018 44300 43031-0019 43031-0051 430310052 430310053 43031-0057 43031-0059 43031-0102 43031-0103 43031-0106 Micro-Fit 3.0 43025 44372 High Force Crimp Terminal 43645 44372-0002 20-24 AWG 44133 Micro-Fit 3.0 43025 46235 Crimp Terminal 43645 46235-0001 46235-0002 46235-0003 46235-0004 20-24 AWG 44133 51004 50011 2.0mm (.079 ) Low Profile 50011-8000 50011-8100 39-00-0422 51049 Receptacle Terminal 51004 24-34 AWG 50031 50031-8000 50031-8100 51049 1.25mm (.049 ) Pitch 50058-8000 50058-8099 50058-8100 50058-8200 50058-8300 50058 51021 PicoBlade Crimp Terminal 50058-8400 50058-8500 26-32 AWG 1.25mm (.049 ) Pitch 50061-8000 50061-8018 50061-8028 50061-8099 50061-8100 50061 51022 Board-In Crimp Terminal 50061-8118 50061-8128 28-32 AWG 50079-8000 50079-8053 50079-8099 50079-8100 50079-8153 1.25mm (.049 ) Pitch 50079 51021 PicoBlade 39-00-0413 39-00-0414 Crimp Terminal 50080 51022 50080-8000 50080-8100 26-28 AWG 50125 51047 50125-8000 50125-8100 1.25mm (.049 ) Pitch 50133 PicoBlade Crimp Terminal 51047 50133-8000 50133-8100 28-32 AWG 2.50mm (.098 ) Pitch 50147 52266 50147-8000 50147-8100 Splash Proof Crimp Terminal 50148 52213 50148-8000 50148-8100 20-22 AWG Doc No: ATS-011030043 Release Date: 02-02-95 UNCONTROLLED COPY Page 1 of 5 Revision: J Revision Date: 02-23-09 HT60923A Extractor Tool Terminal Housings Description Terminal Order No. Series No. Series No. 2.0mm (.079 ) Low Profile 51004 50200 50200-8000 50200-8100 Receptacle Terminal 51049 22-32 AWG Micro-Latch 5109 2.00mm (.079 ) Pitch 50212 51065 50212-8000 50212-8100 50212-8200 50212-8300 39-00-0424 Crimp Terminal 51090 24-30 AWG 2.00mm (.079 ) Pitch 5109 50372 Crimp Terminal 51065 50372-8000 50372-8100 22-26 AWG 51090 4.00mm (.157 ) Pitch 51115 50420 OBD-II Wire-to-Wire 50420-8000 50420-8100 50420-8200 51116 Crimp Terminal 2.00mm (.079 ) Pitch 502443 502438 CLIK-Mate Wire-to-Board 502438-0000 502438-0100 502494 Crimp Terminal, 22-26 AWG Note: All Individual terminals may be extracted from the housing using this Tool. OPERATION: For 43030, 43031, 44372, and 46235 Terminal Series: 1. Insert the tip of the tool on either side of the terminal until it stops. See Figure 1. 2. Rotate tool clockwise then counter-clockwise HOUSING approximately 25 to 30 in each direction, once or twice. PULL OUT 3. Repeat steps 1 and 2 on the opposite side of terminal. TERMINAL 4. Pull on the wire and remove the terminal from the AND WIRE housing. See Figure 2. TIP OF TOOL INSERTED ON THE SIDE OF TERMINAL HOUSING LOCKING TANGS PUSHED IN EXTRACTOR TOOL LOCKING TANGS PUSHED IN Figure 2 EXTRACTOR TERMINAL Figure 1 TOOL NOTE: When a terminal is removed in this manner the locking tangs are damaged and the terminal is not reusable. Doc No: ATS-011030043 Release Date: 02-02-95 UNCONTROLLED COPY Page 2 of 5 Revision: J Revision Date: 02-23-09