SX-ULPGN Hostless 802.11n Wi-Fi Internet-of-Things Platform Optional External MCU Support with Silex UART AT Command Set SX-ULPGN is a low power, cost effective 802.11b/g/n Key Features Internet-of-Things (IoT) platform based on the Qualcomm Single stream (1x1) IEEE 802.11b/g/n conformity (2.4 GHz) QCA4010 System-on-Chip (SoC). SX-ULPGN is a feature-rich intelligent Wi-Fi solution for IoT that integrates a full Wi-Fi stack, Data rate up to 72.2 Mbps MCS7 HT20 full networking/security stack, and embedded CPU and Tensilica Xtensa 7 130 MHz CPU memory for on-chip application development. It includes an integrated RF front end and an internal PCB antenna. Up to 800 Kbytes of RAM available for application code Network and security: TCP/IP, IPv4/IPv6, HTTP, SSL/TLS This module is ideally suited for embedded wireless IoT UART, SPI, I2C, I2S, PWM, ADC, JTAG, and GPIO interfaces products including medical devices, remote control, appliances, home & factory automation, energy management, residential Internal 1.2V and 1.8V regulator and power management unit lighting, security, sensors, wearables, etc. IEEE sleep, fast wake-up, low power Rx listen SX-ULPGN is an FCC/IC & CE certified module. In order to AllJoyn Support expedite your product development process, Silex can provide Embedded ThreadX Real-Time-Operating-System (RTOS) both hardware and software engineering services including custom application development, as well as turnkey product design and manufacturing. Block Diagram DC 3.3V SX-ULPGN 16 Mbit SPI Flash Debug UART Hi-speed UART GPIOs Balun LC Filter Antenna JTAG QCA4010 16 mm PWM ADC I2S I2C 40 MHz XTAL SPI 30 mm SX-ULPGN is based on the QCA4010 Reference Hardware & Software. The Software and documentation is available on the Qualcomm Developer Network: SX-ULPGN Hostless 802.11n Wi-Fi Internet-of-Things Platform Hostless IoT System Use Case Specifications: Cost Effective Solution by SX-ULPGN / QCA4010 Product Name Eliminating External Host SPI Master x 1, Debug UART x 1, High Speed UART The SX-ULPGNs internal CPU can act as a host with the Interfaces x 2, I2C master x 1, I2C Slave x 1, application running from the internal memory. Peripherals I2S x 1, PWM x 6, ADC x 4, JTAG x 1, GPIOs and sensors connect to the CPU using any of the available Operating Voltage 3.3V +/- 10% I/O Supply Voltage interfaces: UART, SPI, I2C, I2S, ADC, PWM, GPIO. Frequency Range 802.11b/g/n: 2.412 2.472 GHz Baseband Specification CSMA/CA with ACK SX-ULGPN Application 802.11b: 11, 5.5, 2, 1 Mbps Peripherals, Data Rates OS 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: Sensors, MCS 0 to 7 Network TCP/IP Control, 802.11b: CCK, DQPSK, DBPSK Wi-Fi Security/Auth Automation Modulation Techniques 802.11g: 64QAM, 16QAM, QPSK, BPSK 802.11n: Wi-Fi MAC BPSK, QPSK, 16QAM, 64QAM Network Operating Modes Station, AP, Concurrent (MCC), Wi-Fi Direct Operating Channels 11: (Ch. 1-11) North America UART AT Command Use Case (2.4GHz) 13: (Ch. 1-13) Europe Simplified Implementation by 802.11b: 17 dBm (US) 14 dBm (EU) (1-11Mbps) 802.11g: 17 dBm (US) 14 dBm (EU) (6 Mbps) Using MCU UART AT Command Interface Transmit Output Power 802.11g: 13 dBm (US, EU) (54 Mbps) SX-ULPGN can also provide Wi-Fi connectivity to an external (Tolerance +/- 1.5 dBm) 802.11n: 17 dBm (US) 14 dBm (EU) (MCS0, HT20) 802.11n: 15 dBm (US) 14 dBm (EU) (MCS4, HT20) host via the UART interface. It can offload the host MCU by 802.11n: 12 dBm (US) 12 dBm (EU) (MCS7, HT20) performing network, security, and authentication. 802.11b: -95 dBm (1 Mbps) Typical Receive Sensitivity 802.11g: -89 dBm (6 Mbps) SX-ULGPN External 802.11n: -89 dBm (MCS0, HT20) Host MCU Peripherals, Rx: 76 mA (TCP downlink) Current Consumption UART Tx: 124 mA (TCP uplink) Network TCP/IP Application (Typical, 11ng, HT20) 3.3V Sensors, Standby: 13 uA (Suspend), 450 uA (DTIM3) Wi-Fi Security/Auth OS Control, WPA, WPA2, WPS, WEP 64/128 Security Wi-Fi MAC UART AT Automation OS Supported ThreadX & Qualcomm AllJoyn Platform Operating: 0 +70 Degrees C (Ambient) Temperature Ordering Information Storage: -40 +85 Degrees C (Ambient) SX-ULPGN-2000 Bulk SKU Operating: 5 90% (Non-condensing) Storage: 5 Relative Humidity SX-ULPGN-2000-SP Sample Pack 95% (Non-condensing) Package SX-ULPGN-EVK Evaluation Kit 46 Pin Solder Down stamp Format SX-ULPGN is based on the QCA4010 Reference Hardware & Software. The Software and documentation is available on the Qualcomm Developer Network: