10.5 D 120 Mounting Accessories www.vishay.com Vishay BCcomponents Aluminum Capacitors MECHANICAL DATA CLAMPS FOR ST TYPES To facilitate vertical mounting, a series of rigid clamps is available. These are made of zinc plated steel, chromium (III) passivated, or stainless steel ( D = 76 mm). The clamps have either two or three mounting lugs, may be easily slipped over the capacitor and then clamped with a nut and bolt. Five types of clamps are available, one for each case diameter. They are delivered without nuts or bolts, except for D = 90 mm, where they are included. To avoid damaging the insulation sleeve, do not overtighten the clamp screw. DIMENSIONS in millimeters AND AVAILABLE FORMS 12.05 12 0.5 11.05 7 1 6 6 1 1 12.5 max. 60 63 10.5 4 min. 51.5 0.2 35 4.4 min 60 12 0 4.5 0.5 - 0.5 35 50 49 23.5 10 67.5 4.5 0.1 66.5 80 max. Fig. 1 - Dimensional outline of clamp for case D = 35 mm Fig. 2 - Dimensional outline of clamp for case D = 50 mm 12.5 19 28.5 11.5 7 1 1 6 12.5 max. 15 4.5 60 10.5 4.5 4.4 min. 12.5 60 7 89 65 99 64 88.5 87.5 101 max. Fig. 3 - Dimensional outline of clamp for case D = 65 mm Fig. 4 - Dimensional outline of clamp for case D = 76 mm 11 5.5 24 0.5 30 1 4.5 4.5 0.5 90 101.6 0.5 111.1 1 Fig. 5 - Dimensional outline of clamp for case D = 90 mm Revision: 26-Aug-15 Document Number: 28348 1 For technical questions, contact: aluminumcaps2 vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 120(3 x) 5 0.3 10.5 14 7 1 4.2 0.1 12 Mounting Accessories www.vishay.com Vishay BCcomponents Table 1 MOUNTING CLAMPS FOR SCREW TERMINALS CASE DIAMETER ORDERING CODE 35 MAL804324031E3 50 MAL804324051E3 65 MAL804324061E3 76 MAL804323321E3 90 MAL804324921E3 NUTS AND WASHERS FOR STB-VERSIONS When mounting with the bolt, which is an integral part of the case, standard metal M8 and M12 nuts and washers may be used the maximum permissible torque is 4 Nm for M8 nuts and 10 Nm for M12 nuts. If insulated mounting is required, synthetic nuts and rubber washers are available for these nuts the maximum permissible torque is 2 Nm (M8) and 4 Nm (M12). DIMENSIONS in millimeters AND AVAILABLE FORMS D 1 17 0.3 Rubber washer H 6 W Fig. 6 - Insulated mounting Fig. 7 - Synthetic cap nut see Table 2 for dimensions D, H and W Table 2 SYNTHETIC CAP NUTS (1) CASE DIAMETER D H W MIN. THREADED DEPTH THREAD ORDERING CODE (mm) (mm) (mm) (mm) (mm) 35 M8 25 15 17 11.5 MAL804305561E3 50 M12 30 20 19 15.5 MAL804305571E3 Note (1) Dimension W is measured across flats. D d 0.2 Fig. 8 - Rubber washer thickness 2 mm RUBBER WASHERS D d ORDERING CODE (mm) (mm) 34 8.4 MAL804305591E3 49 13.0 MAL804305531E3 64 13.0 MAL804305521E3 74 13.0 MAL804313001E3 88 13.0 MAL804329961E3 Revision: 26-Aug-15 Document Number: 28348 2 For technical questions, contact: aluminumcaps2 vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000