200-6319-9UN-1900 3M

Test & Burn-In PGA Kit Sockets Pin Grid Arrays Available in 10 x 10 matrix through 25 x 25 matrix Used when only a few test sockets are needed Provides individual components ready for assembly Open pattern top plate load only those contacts needed for your specific device pin pattern TS-0675-09 Sheet 1 of 2 Date Issued: June 20, 2001 10 Physical Insulation Material: Polyethersyfone (PES) Flammability: UL 94V-0 Color: Black Marking: 3M Logo & Part Number Identifier Cam Handle Material: Stainless Steel Contact Material: Beryllium Copper Plating Options: 30 (0.76 mm) Gold over 50 (1.3 mm) Nickel Electrical Current Rating: 1 Amp 12 Insulation Resistance: > 1 10 W at 500 Vdc Withstanding Voltage: 1000 Vrms at Sea Level Environmental Temperature Rating Operating: - 55C to + 150C Mechanical A: When used as a test socket at room temperature 24C the socket will last 25,000 actuations. B: Based on field experience, under normal burn-in conditions up to a maximum of 150C, the socket should last an average of four years. 3M Electronic Handling and Protection Division 6801 River Place Blvd. For technical, sales or ordering information call 800-328-0411 Austin, TX 78726-9000 or visit our website: Test & Burn-In PGA Kit Socket Pin Grid Arrays Assembly Instructions 1. Load hole plugs into top plate by pressing fitting into place. 4X Phillips Pan-Hd Remove from tie bar by cutting 0-80 x 5/16 Long Assy Screw with commercially available 6 1/2 flush diagonal cutter pliers. 1 10X Hole Plugs 2. Place cam plate into recessed area of base plate, load contacts in desired locations, being careful that the bent leaf of the contact is loaded in correct position ( away from cam handle. ) 3. Insert cam handle into position in the base plate. 4. Now make a final check that all contacts are in desired location and that all are fairly even at the Top Plate top. Also check cam to make sure it is still in position. Now take the top plate and place into position and start to lower over Contact contacts. Start at the rear of the ( Order Separately ) socket and rotate downward toward the front and then snap locating bosses into place. Several very slight back and Cam Plate forth motions may be necessary in order to get contacts to snap into place. Care should be taken that too much downward pressure isn t applied which could bend or damage the contacts. Insert screws and tighten. 5. Now make an operation check by rotating handle 90. Make a visual check of movement and Cam Handle closure of all contacts. Rotate Base Plate handle and check the freedom of movement of cam plate and that the moving leaf of the Standard contact clears the entry hole. A Handle continuity check can be made before final soldering by placing device in socket, then closing Notes: and making check. Soldering 1 Contact and extra Hole Plugs are ordered separately. should be done with socket in 2 See Test & Burn-In PGA socket section on page 29 for dimensional information on assembled sockets. the open position. Ordering Information Part Number Matrix Size Description 200-6310-9UN-1900 10 x 10 200-6311-9UN-1900 11 x 11 200-6313-9UN-1900 13 x 13 200-6315-9UN-1900 15 x 15 SSockkett KKiitt WW//OO CConttactts 200-6317-9UN-1900 17 x 17 200-6319-9UN-1900 19 x 19 200-6321-9UN-1900 21 x 21 200-6325-9UN-1900 25 x 25 300-6300-CNA-0002B Each ContactBeCu/Au Plated 200-4660-14-1900 Set of 10 Extra Hole Plugs TS-0675-09 Sheet 2 of 2 3M Electronic Handling and Protection Division For technical, sales or ordering information call 800-328-0411 6801 River Place Blvd. Austin, TX 78726-9000 or visit our website: