DATASHEET 6A Analog PicoDLynxTM: Non-Isolated DC- DC Power Modules 3Vdc - 14.4Vdc input 0.6Vdc to 5.5Vdc output 6A Output Current The 6A Analog PicoDLynxTM power modules RoHS Compliant are non-isolated dc-dc converters that can deliver up to 6A of output current. These modules operate over a wide range of input voltage (VIN = 3Vdc-14.4Vdc) and provide a precisely regulated output voltage from 0.6Vdc to 5.5Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and over temperature protection. The Tunable LoopTM feature allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. Applications Distributed power architectures Servers and storage applications Intermediate bus voltage applications Networking equipment Telecommunications equipment Industrial equipment Features Compliant to RoHS Directive 2011/65/EU and amended Fixed switching frequency Directive (EU) 2015/863. Output overcurrent protection (non-latching) Compliant to REACH Directive (EC) No 1907/2006. Over temperature protection Compatible in a Pb-free or SnPb reflow environment (Z Remote On/Off versions) Ability to sink and source current Compliant to IPC-9592 (September 2008), Category 2, Class II Cost efficient open frame design Use ABB specified module version and process for SMT Small size: 12.2 mm x 12.2 mm x 7.25 mm 0.48 in x 0.48 placement on bottom side of board (-D version only) in x 0.29 in) DOSA based Wide operating temperature range -40C to 105C Wide Input voltage range (3Vdc-14.4Vdc). Ref. to Figure 42 for (Ruggedized: -D), 85C(Regular) corresponding output range. ANSI/UL* 62368-1 and CAN/CSA C22.2 No. 62368-1 Output voltage programmable from 0.6Vdc to 5.5Vdc via Recognized, DIN VDE 0868-1/A11:2017 (EN62368-1:2014/ external resistor A11:2017) Tunable LoopTM to optimize dynamic output voltage response ISO** 9001 and ISO 14001 certified manufacturing facilities Power Good signal * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Page 1 Version 1.6 2021 ABB. All rights reserved. Technical Specifications Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage: Continuous All V -0.3 15 Vdc IN Operating Ambient Temperature All T -40 85 C A (See Thermal Considerations Section) Storage Temperature All T -55 125 C stg Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. INPUT Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All V 3* 14.4 Vdc IN Maximum Input Current All I 5.6 Adc IN,max (V =3V to 14V, I =I ) IN O O, max V = 0.6 Vdc I 25 mA O,set IN,No load Input No Load Current (V = 12.0Vdc, I = 0, module enabled) IN O V = 5Vdc I 55 mA O,set IN,No load Input Stand-by Current All I 0.65 mA IN,stand-by (V = 12.0Vdc, module disabled) IN 2 2 Inrush Transient All I t 1 A s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1 H source impedance V =0 to All 23 mAp-p IN 14V I = I See Test Configurations) , O Omax Input Ripple Rejection (120Hz) All -60 dB *Module needs 3.3Vin for operation at full load, -40C Page 2 Version 1.6 2021 ABB. All rights reserved.