SpecMat-H Static Dissipative Homogeneous Material The SpecMat-H homogeneous material is a single-layer, ESD-safe thermoplastic vinyl made for bench tops. Without adding cost, the extruded manufacturing process used to produce this high-per- formance vinyl utilizes superior plasticizers and lower-outgassing solvents, unlike ESD vinyl made by cast coating. The proprietary polymers used to manufacture this material are homogeneously dispersed with a migratory anti-static formula that allows for both surface and volume resistance. By design, anti-static properties cannot be worn away through wear or outgassing. Resistant to solder, heat, and most common solvents, SpecMat-H is an economical choice for static- sensitive production areas in Color shown is a representation and may vary electronics manufacturing and laboratories. Tray mats can be cus- tom-cut with a sharp blade. Scraps can be recycled. Maintenance: To keep mats clean and avoid insulative Blended with hydrophilic molecules to control the speed of dissipa- tion, the ESD-Homogeneous material will deliver a typical resis- electrical readings, use a neutral cleaner 8 9 tance-to-ground measurement of 10 -10 ohms per ANSI/ESD S4.1. such as the 6001 Mat and Table Top ESD-Homogeneous material complies with industry standards Cleaner. The low alcohol, high surfac- including EN 61340-5-1: Protection of Electronic Devices from Elec- tant formula will allow deep cleaning trostatic Phenomena and ANSI ESD S20.20: Protection of Electrical without damaging the structural integ- and Electronic Parts, Assemblies and Equipment. rity of the SpecMat-H material. 0.10 (2.54 mm) thickness SpecMat-H roll 8 9 10 - 10 ohms, ohm per cm RTG, RTT, Vol R 62100 light blue 24 x 40 62300 light blue 30 x 40 Can be custom-cut with sharp blade scraps are recyclable 62500 light blue 36 x40 Embossed finish reduces light glare and parts slippage SpecMat-H cut mats are available in various Durable surface withstands high temperatures, solder, flux, and sizes. Each mat includes two 10mm female harsh chemicals ground snaps. Ground cords sold separately. Low outgassing and VOC are ideal for controlled environments Passes weathering ozone resistance per ASTM D178-01 The components used to manufacture Passes and exceeds minimum standards for NFPA fire and this product, including smoke and flame smoke safety inhibitors, are RoHS compliant and are not UV additives to protect color and eliminate fading listed on the REACH SvHC list. Warranty: Rolls and cut mats are made in the U.S.A. 8 9 ACL Inc., offers an exclusive lifetime warranty on the electrical resistance (10 10 and can be shipped under NAFTA rules. ohms) properties of the SpecMat-H table mats. If the electrical properties should fail (when tested to ANSI / ESD S20.20) on any of our table mats during the lifetime of the mat due to manufacturing or physical defects, we will replace the mat free of charge. This warranty does not apply to mats that are abused, improperly used, or cleaned with mat cleaners not tested and approved by ACL Inc. ACL Inc. registered to ISO-9001 : 2008 840 W. 49th Place Chicago, IL 60609 Certificate No. 10002746 800.782.8420 847.981.9212 fax 847.981.9278 info aclstaticide.com www.aclstaticide.com rev. January 5, 2015 mkbFor SpecMat-H .10 Thickness: BULK roll manufacturer part numbers: 62100 24 x 40 62300 30 x 40 62500 36 x 40 PRECUT SIZE manufacturer part numbers: 6212436 24 x 36 6212460 24 x 60 6212472 24 x 72 6233060 30 x 60 6233072 30 x 72 6253660 36 x 60 6253672 36 x 72