PRODUCT INFORMATION Sugru by tesa 41231 - 41237, 41281 - 41287 1-RTV (room temperature vulcanising) moisture-activated, hand mouldable glue that turns into a flexible silicone rubber. Main Applications Sugru hand mouldable glue is suitable for durable repairs, gap-filling, non-drilling mounting and cable reinforcing applications. Holds its shape while curing, non shrinking, for complex irregular shapes and customised designs. Minimal mess and skin safe. Long-lasting and flexible bonding to glass, ceramic, wood, metal and most plastics. Suitable for indoor and outdoor use and many applications requiring waterproof properties. For optimum results: Preparation: The surface to be bonded should be clean and dry. Remove dust from the surface using a dust-free cloth or an alcohol wet wipe. Application: Open the pack and use Sugru within 30 min. Simply stick it, mould it by hand, and in 12-24 hrs it turns into a flexible silicone rubber. Removal: Remove Sugru from non-porous surfaces by cutting off the bulk of the Sugru using a knife or scalpel. You can then remove the residue with your nail and some tissue. Please note: Cure time is influenced by the area of Sugru which is exposed to the air, volume of Sugru, air temperature and humidity. Warmer and more humid air will increase the cure rate. Thicker applications may take longer to cure so for heavy load bearing projects or where the exposure of Sugru to air is limited, e.g. squashed between two surfaces, allow 48 hrs to set and test first. Store in a dry and cool place. To extend shelf-life store unopened packs in the fridge (or freezer). Suitable only for small consumer electronic repairs with low voltage and low current (up to 24 volts). Not recommended for bonding to oily plastics such as PE, PP and Teflon. After use, remove any Sugru residues from skin using paper towel then wash your hands with warm water and soap. Adhesion Properties The graph was generated by testing Sugru on a range of materials according to ASTM D 1002. Samples of lap shear joints with 2 mm thickness, 25.4 mm width and 12.7 mm overlap were tested after 24 hrs curing at 25 C and 50% relative humidity. FForor thefurtherlateisnft orminformationationconontacthit tecs produchnical st pleaugsreu.vciomsit PRODUCT INFORMATION Technical Data & Properties Consistency Putty-like adhesive that turns into a flexible rubber after exposure to air. Working Time 30 min at room conditions (25C and 50% relative humidity). Approximately 24 hr cure for the first 3 mm of depth at 25C and 50% relative Cure Time humidity, e.g. 1.5 mm cures in ~ 12 hrs, 3 mm cures in ~ 24 hrs. 22 month shelf-life from the date of manufacture when stored at room conditions in Shelf-Life original unopened packaging. Supplied in 10 different colours. When uncured the colours can be mixed just like Colour paint to make any colour knead together thoroughly for a uniform colour. Equivalent to 5 years real-life weather exposure (UV visible and infrared radiation) UV Resistance according to Florida test ISO 4892. Temperature Resistance Between -40C (-40F) and 180 C (356F) . Tested for at least 10 x 8 hrs cycles. Very good. 1 mm cured sheet can withstand liquid (tap water) up to a pressure of 12 Water Resistance PSI at room conditions. Dielectric Strength 13.5 0.8 kV/mm according to ASTM D149-09 (2013) Method A, Short-Time Test. 160 260 % according to ASTM D 638 when cured for 24 hrs at 25C and 50% Elongation at Fracture relative humidity. Additional Information & Pictures 41231 - 41237 3 x 3.5g single use packs 41281 - 41287 8 x 3.5g single-use packs FForor thefurtherlateisnft orminformationationconontacthit tecs produchnical st pleaugsreu.vciomsit