LV-MaxSonar - EZ Series LV-MaxSonar -EZ Series High Performance Sonar Range Finder 2 MB1000, MB1010, MB1020, MB1030, MB1040 With 2.5V - 5.5V power the LV-MaxSonar-EZ provides very short to long-range detection and ranging in a very small package. The LV-MaxSonar-EZ detects objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from 6- inches out to 254-inches with 1-inch resolution. Objects from 0-inches to 6-inches typically range 1 as 6-inches . The interface output formats included are pulse width output, analog voltage output, and RS232 serial 1 output. Factory calibration and testing is completed with a flat object. See Close Range Operation Sensor operates at 42KHz Applications and Uses Features High output square wave sensor drive UAV blimps, micro planes and some Continuously variable gain for control (double Vcc) helicopters and side lobe suppression Actual operating temperature range from Bin level measurement Object detection to zero range objects 40C to +65C, Recommended Proximity zone detection 2.5V to 5.5V supply with 2mA typical operating temperature range from 0C to 1 People detection current draw +60C Robot ranging sensor Readings can occur up to every 50mS, Benefits (20-Hz rate) Autonomous navigation Very low cost ultrasonic rangefinder Free run operation can continually Multi-sensor arrays Reliable and stable range data measure and output range information Distance measuring Quality beam characteristics Triggered operation provides the range Long range object detection reading as desired Mounting holes provided on the circuit Wide beam sensitivity board Interfaces are active simultaneously Very low power ranger, excellent for Serial, 0 to Vcc, 9600 Baud, 81N Notes: multiple sensor or battery-based systems 1 Please reference page 4 for minimum operating Analog, (Vcc/512) / inch Fast measurement cycles voltage verses temperature information. Pulse width, (147uS/inch) 2 Please reference page 12 for part number key. Sensor reports the range reading directly Learns ringdown pattern when and frees up user processor commanded to start ranging Choose one of three sensor outputs Designed for protected indoor environments Triggered externally or internally LV-MaxSonar-EZ Mechanical Dimensions K Part Num- MB1000 MB1010 MB1020 MB1030 MB1040 J ber Paint Black Brown Red Orange Yellow Paint Dot Location Dot Color Close Range Operation Applications requiring 100% reading-to-reading reliability should not use MaxSonar sensors at a distance closer than 6 inches. Although most users find MaxSonar sensors to work reliably from 0 to 6 inches for detecting objects in many applications, MaxBotix Inc. does not guarantee operational reliability for objects closer than the minimum reported distance. Because of ultrasonic physics, these sensors are unable to achieve 100% reliability at close distances. Warning: Personal Safety Applications We do not recommend or endorse this product be used as a component in any personal safety applications. This product is not designed, intended or authorized for such use. These sensors and controls do not include the self-checking redundant circuitry needed for such use. Such unauthorized use may create a failure of the MaxBotix Inc. product which may result in personal injury or death. MaxBotix Inc. will not be held liable for unauthorized use of this component. Page 1 MaxBotix Inc., products are engineered and assembled in the USA. MaxBotix Inc. Web: www.maxbotix.com Copyright 2005 - 2021 MaxBotix Incorporated PD11832h Patent 7,679,996 LV-MaxSonar - EZ Series About Ultrasonic Sensors Our ultrasonic sensors are in air, non-contact object detection and ranging sensors that detect objects within an area. These sensors are not affected by the color or other visual characteristics of the detected object. Ultrasonic sensors use high frequency sound to detect and localize objects in a variety of environments. Ultrasonic sensors measure the time of flight for sound that has been transmitted to and reflected back from nearby objects. Based upon the time of flight, the sensor then outputs a range reading. Pin Out Description Pin 1-BW-*Leave open or hold low for serial output on the TX output. When BW pin is held high the TX output sends a pulse (instead of serial data), suitable for low noise chaining. Pin 2-PW- This pin outputs a pulse width representation of range. The distance can be calculated using the scale factor of 147uS per inch. Pin 3-AN- Outputs analog voltage with a scaling factor of (Vcc/512) per inch. A supply of 5V yields ~9.8mV/in. and 3.3V yields ~6.4mV/in. The output is buffered and corresponds to the most recent range data. Pin 4-RX This pin is internally pulled high. The LV-MaxSonar-EZ will continually measure range and output if RX data is left unconnected or held high. If held low the sensor will stop ranging. Bring high for 20uS or more to command a range reading. Pin 5-TX- When the *BW is open or held low, the TX output delivers asynchronous serial with an RS232 format, except voltages are 0-Vcc. The output is an ASCII capital R, followed by three ASCII character digits representing the range in inches up to a maximum of 255, followed by a carriage return (ASCII 13). The baud rate is 9600, 8 bits, no parity, with one stop bit. Although the voltage of 0-Vcc is outside the RS232 standard, most RS232 devices have sufficient margin to read 0-Vcc serial data. If standard voltage level RS232 is desired, invert, and connect an RS232 converter such as a MAX232. When BW pin is held high the TX output sends a single pulse, suitable for low noise chaining. (no serial data) Pin 6-+5V- Vcc Operates on 2.5V - 5.5V. Recommended current capability of 3mA for 5V, and 2mA for 3V. Please reference page 4 for minimum operating voltage verses temperature information. Pin 7-GND- Return for the DC power supply. GND (& Vcc) must be ripple and noise free for best operation. Range 0 Location The LV-MaxSonar-EZ reports the range to distant targets starting from the front of the sensor as shown in the diagram below. Range Zero The range is measured from the front of the transducer. In general, the LV-MaxSonar-EZ will report the range to the leading edge of the closest detectable object. Target detection has been characterized in the sensor beam patterns. Sensor Minimum Distance The sensor minimum reported distance is 6-inches (15.2 cm). However, the LV-MaxSonar-EZ will range and report targets to the front sensor face. Large targets closer than 6-inches will typically range as 6-inches. Sensor Operation from 6-inches to 20-inches Because of acoustic phase effects in the near field, objects between 6-inches and 20-inches may experience acoustic phase cancellation of the returning waveform resulting in inaccuracies of up to 2-inches. These effects become less prevalent as the target distance increases, and has not been observed past 20-inches. Page 2 MaxBotix Inc., products are engineered and assembled in the USA. MaxBotix Inc. Web: www.maxbotix.com Copyright 2005 - 2021 MaxBotix Incorporated PD11832h Patent 7,679,996