CYAN MAGENTA YELLOW BLACK CYAN MAGENTA YELLOW BLACK TGP110 10MHz pulse generator with delay An essential instrument Wide pulse range The generation of pulses for the stimulus and control of elec- The TGP110 can generate pulse widths in the range 50ns to 5s. tronic systems is beyond the capability of all but the most so- There are eight overlapping decade ranges with vernier control phisticated of function generators. within each range. The architecture of a dedicated pulse generator enables it to The period range is 100ns to 10s, equivalent to a repetition rate generate pulses of a set width regardless of the repetition rate range of 10MHz to 0.1Hz. Delay is independently adjustable offering duty cycles which can extend down to 1 in 100 million. over the same range as pulse width. AIM & THURLBY THANDAR INSTRUMENTS In addition to continuous operation, single or multiple pulses A complement switch inverts the mark-space polarity. can be generated in response to trigger or gating signals with TGP110 precisely defined timing relationships. Squarewave and double pulse A dedicated pulse-waveform output amplifier provides flat top In square mode, squarewaves are generated at a frequency set pulses with fast rise and fall times at variable amplitude. by the period controls alone. This provides a convenient means of generating variable period edges where the pulse width is Variable delay unimportant, for example. The TGP110 offers selectable delay between the sync output In double pulse mode, a second pulse is generated within every and pulse output. In triggered mode this also sets the delay be- period at a set delay after the start of the first pulse. The delay is tween a trigger signal and the start of the pulse. independently adjustable. PERIOD, PULSE WIDTH, DELAY INPUTS Each parameter is variable within 8 overlapping decade ranges with a GATE/TRIG INPUT vernier providing continuously variable control within each range. Frequency range: DC - 10MHz PERIOD Signal range: TTL threshold max. input 10V. Range: 100nsec to 10sec (10MHz to 01Hz). Min. pulse width: >30nsec. Jitter: <0.1%. Input Impedance: Typically 10k . PULSE WIDTH Range: 50nsec to 5sec OUTPUTS Jitter: <0.1%. DELAY 50 OUTPUT Range: 50nsec to 5sec Amplitude: Two switch selectable ranges of 01V - 10V and 1V - 10V from 50 . (50mV to 500mV and 500mV to 5V into 50 ). Adjustable within ranges by a single TRIGGER, GATE turn vernier. Rise/Fall Times: RUN Typically 10nsec into 50 load. Maximum 15ns. Aberrations: Typically <5% for output set at >20% of range maxi- Normal operational mode in which pulses are generated continuously at 0.1Hz to 10MHz. mum, into 50 . TRIGGERED AUX OUTPUT DC to 10MHz pulse train in synchronism with external trigger pulses Duplicates 50 output but at a fixed CMOS/TTL level. pulse width determined by pulse width controls. Trigger can be gener- SYNC OUTPUT ated manually from front panel button. Amplitude: A positive going pulse at CMOS/TTL level. GATED Timing: Leading edge starts >20nsec before the TTL/50 01Hz to 10MHz pulse train, parameters set by period and pulse width output transition. controls, starts synchronously with leading edge of gate input. Last pulse Duration: Typically 30nsec. is completed at the end of gating period. Gating signal can be generated COMPLEMENT SWITCH manually from front panel button. Inverts the AUX and 50 outputs. PULSE MODES GENERAL NORMAL PULSE Power: 230V or 115V AC nominal 50/60Hz, adjustable inter- One pulse is generated each period. The delay setting is ignored. nally operating range 14% of nominal 20VA max. SQUAREWAVE Size: 140 x 220 x 230mm (HxWxD) 10MHz pulse generator with delay 01Hz to 10MHz squarewave, frequency set by the period controls. Weight: 1.6kg (3.5lb) Pulse width and delay settings ignored. Operating Range: + 5C to 40C, 20-80% RH. Mark : Space ratio: 1:1 10%. Storage Range: - 40C to 70C DOUBLE PULSE Safety: Complies with EN61010-1. 0.1Hz to 10MHz frequency range A second pulse is generated after a delay set by the delay controls the EMC: Complies with EN55081-1 and EN50082-1. delay is related to the leading edge of the first pulse. 50ns minimum pulse width fully variable pulse delay DELAYED PULSE A pulse is generated after a delay set by the delay controls the delay is Thurlby Thandar Instruments Ltd. operates a policy of continuous development and reserves related to rising edge of the trigger signal. the right to alter specifications without prior notice. Squarewave, double pulse and delayed pulse modes Free-run, gated and triggered modes Designed and built in Europe by: 50 output, variable 0.1V to 10V TTL and sync outputs Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon. Cambs. PE29 7DR England Tel: +44 (0)1480 412451 Fax: +44 (0) 1480 450409 Email: info aimtti.com Web: www.aimtti.com 82100-0066 Iss. 1ACYAN MAGENTA YELLOW BLACK CYAN MAGENTA YELLOW BLACK TGP110 10MHz pulse generator with delay An essential instrument Wide pulse range The generation of pulses for the stimulus and control of elec- The TGP110 can generate pulse widths in the range 50ns to 5s. tronic systems is beyond the capability of all but the most so- There are eight overlapping decade ranges with vernier control phisticated of function generators. within each range. The architecture of a dedicated pulse generator enables it to The period range is 100ns to 10s, equivalent to a repetition rate generate pulses of a set width regardless of the repetition rate range of 10MHz to 0.1Hz. Delay is independently adjustable offering duty cycles which can extend down to 1 in 100 million. over the same range as pulse width. AIM & THURLBY THANDAR INSTRUMENTS In addition to continuous operation, single or multiple pulses A complement switch inverts the mark-space polarity. can be generated in response to trigger or gating signals with TGP110 precisely defined timing relationships. Squarewave and double pulse A dedicated pulse-waveform output amplifier provides flat top In square mode, squarewaves are generated at a frequency set pulses with fast rise and fall times at variable amplitude. by the period controls alone. This provides a convenient means of generating variable period edges where the pulse width is Variable delay unimportant, for example. The TGP110 offers selectable delay between the sync output In double pulse mode, a second pulse is generated within every and pulse output. In triggered mode this also sets the delay be- period at a set delay after the start of the first pulse. The delay is tween a trigger signal and the start of the pulse. independently adjustable. PERIOD, PULSE WIDTH, DELAY INPUTS Each parameter is variable within 8 overlapping decade ranges with a GATE/TRIG INPUT vernier providing continuously variable control within each range. Frequency range: DC - 10MHz PERIOD Signal range: TTL threshold max. input 10V. Range: 100nsec to 10sec (10MHz to 01Hz). Min. pulse width: >30nsec. Jitter: <0.1%. Input Impedance: Typically 10k . PULSE WIDTH Range: 50nsec to 5sec OUTPUTS Jitter: <0.1%. DELAY 50 OUTPUT Range: 50nsec to 5sec Amplitude: Two switch selectable ranges of 01V - 10V and 1V - 10V from 50 . (50mV to 500mV and 500mV to 5V into 50 ). Adjustable within ranges by a single TRIGGER, GATE turn vernier. Rise/Fall Times: RUN Typically 10nsec into 50 load. Maximum 15ns. Aberrations: Typically <5% for output set at >20% of range maxi- Normal operational mode in which pulses are generated continuously at 0.1Hz to 10MHz. mum, into 50 . TRIGGERED AUX OUTPUT DC to 10MHz pulse train in synchronism with external trigger pulses Duplicates 50 output but at a fixed CMOS/TTL level. pulse width determined by pulse width controls. Trigger can be gener- SYNC OUTPUT ated manually from front panel button. Amplitude: A positive going pulse at CMOS/TTL level. GATED Timing: Leading edge starts >20nsec before the TTL/50 01Hz to 10MHz pulse train, parameters set by period and pulse width output transition. controls, starts synchronously with leading edge of gate input. Last pulse Duration: Typically 30nsec. is completed at the end of gating period. Gating signal can be generated COMPLEMENT SWITCH manually from front panel button. Inverts the AUX and 50 outputs. PULSE MODES GENERAL NORMAL PULSE Power: 230V or 115V AC nominal 50/60Hz, adjustable inter- One pulse is generated each period. The delay setting is ignored. nally operating range 14% of nominal 20VA max. SQUAREWAVE Size: 140 x 220 x 230mm (HxWxD) 10MHz pulse generator with delay 01Hz to 10MHz squarewave, frequency set by the period controls. Weight: 1.6kg (3.5lb) Pulse width and delay settings ignored. Operating Range: + 5C to 40C, 20-80% RH. Mark : Space ratio: 1:1 10%. Storage Range: - 40C to 70C DOUBLE PULSE Safety: Complies with EN61010-1. 0.1Hz to 10MHz frequency range A second pulse is generated after a delay set by the delay controls the EMC: Complies with EN55081-1 and EN50082-1. delay is related to the leading edge of the first pulse. 50ns minimum pulse width fully variable pulse delay DELAYED PULSE A pulse is generated after a delay set by the delay controls the delay is Thurlby Thandar Instruments Ltd. operates a policy of continuous development and reserves related to rising edge of the trigger signal. the right to alter specifications without prior notice. Squarewave, double pulse and delayed pulse modes Free-run, gated and triggered modes Designed and built in Europe by: 50 output, variable 0.1V to 10V TTL and sync outputs Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon. Cambs. PE29 7DR England Tel: +44 (0)1480 412451 Fax: +44 (0) 1480 450409 Email: info aimtti.com Web: www.aimtti.com 82100-0066 Iss. 1A