Click on Series name for product info on aimtec.com Series AM2GW-Z 2 Watt DC-DC Converter FEATURES: SIP9 Package Ultra-Wide Input Range 4:1 Low Ripple and Noise 1500VDC I/O Isolation Continuous Short Circuit Protection Efficiency up to 85% -40C to +85C Operating Temperature Range Remote ON / OFF Control Models Single output Output Output Maximum Input Current Input Efficiency Model Voltage Current Max Capacitive Load Full Load No Voltage (V) (%) (V) (mA) (F) Load (mA) AM2GW-2403SZ 9-36 3.3 500 2200 92 10 75 AM2GW-2405SZ 9-36 5 400 1000 103 10 82 AM2GW-2412SZ 9-36 12 165 165 100 10 85 AM2GW-2415SZ 9-36 15 135 100 98 10 84 AM2GW-4803SZ 18-75 3.3 500 2200 46 5 75 AM2GW-4805SZ 18-75 5 400 1000 53 5 80 AM2GW-4812SZ 18-75 12 165 165 50 5 84 AM2GW-4815SZ 18-75 15 135 100 50 5 83 Models Dual output Output Output Maximum Input Current Input Efficiency Model Voltage Current Max Capacitive Load Full Load No Voltage (V) (%) (V) (mA) (F) Load (mA) AM2GW-2405DZ 9-36 5 200 470 103 10 82 AM2GW-2412DZ 9-36 12 85 100 101 10 84 AM2GW-2415DZ 9-36 15 65 47 102 15 82 AM2GW-4805DZ 18-75 5 200 470 53 5 80 AM2GW-4812DZ 18-75 12 85 100 52 5 82 AM2GW-4815DZ 18-75 15 65 47 50 5 81 Input Specifications Parameters Nominal Typical Maximum Units 24 9-36 Voltage range VDC 48 18-75 Filter Capacitor Start up time 10 ms 24Vin 50 Absolute Maximum Rating VDC 48Vin 100 Peak Input Voltage time 100 ms On/Off Control ON: 0 to 0.6VDC (or open) OFF:2.7 to 15.0VDC ,OFF: idle current: 5mA, max Input reflected ripple current 20 mA p-p Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 sec 1500 VDC Resistance >1000 MOhm Capacitance 500 pF www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R11.F 1 of 5 North America only Series AM2GW-Z 2 Watt DC-DC Converter Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy 1 % nd Cross Regulation (Dual Output Models) 25% load on output - 100% load 2 output 5 % Short Circuit protection Hiccup Continuous Short circuit restart Auto-Recovery Transient Response Deviation 3 % Transient Recovery Time 300 s Line voltage regulation LL~HL 0.5 % From 10% to 100% load 0.5 Load voltage regulation From 0% to 100% load 12Vout and 15Vout 0.5 % From 0% to 100% load 3.3Vout and 5Vout 1 Ripple & Noise 20MHz Bandwidth 50 mV p-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 250 KHz o Operating temperature -40 to +85 C o Storage temperature -40 to +125 C o Temperature coefficient 0.02 %/ C o Maximum case temperature 100 C Derating Above 75C 3.5 %/C Cooling Free Air Convection Humidity 95 % RH Case material Non conductive black plastic Potting Material Epoxy (UL94V-0 rated) Weight 6.5 g Dimensions (L x W x H) 1.02 x 0.36 x 0.49 inches 26.00 x.9.30 x 12.44 mm MTBF >1,212,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25C) o Max Soldering Temperature 1.5mm from case 10 second 260 C NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Safety Specifications Parameters Agency Approval CE EN55022 Class A, IEC61000-4-2, Perf. Criteria B IEC61000-4-3, Perf. Criteria A IEC61000-4-4, Perf. Criteria B (external 220uF/100V cap required) Standards IEC61000-4-5, Perf. Criteria B (external 220uF/100V cap required) IEC61000-4-6, Perf. Criteria A IEC61000-4-8, Perf. Criteria A NOTE: designed to meet IEC 60950-1:2001 Pin Out Specifications Single Dual Pin 1 - V Input - V Input 2 + V Input + V Input 3 On/Off Control On/Off Control 6 + V Output + V Output 7 NC Common 8 NC NC 9 - V Output -V Output www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R11.F 2 of 5 North America only