Click on Series name for product info on aimtec.com Series AM2L-NZ 2 Watt DC-DC Converter FEATURES: Low Profile SMD MTBF>1,000,000 hours 1000VDC & 6000VDC Isolation Operating temperature: -40C to +85C Industry Standard Pinout High Efficiency up to 85% Unregulated Single & Dual Outputs Models Single output Output Voltage Output Current Isolation Efficiency Model Input Voltage(V) (V) max(mA) (VDC) (%) AM2L-0515S-NZ 4.5-5.5 15 133 1000 84 AM2L-0505SH60-NZ 4.5-5.5 5 400 6000 77 AM2L-1205SH60-NZ 10.8-13.2 5 400 6000 78 AM2L-1215SH60-NZ 10.8-13.2 15 133 6000 81 AM2L-2405SH60-NZ 21.6-26.4 5 400 6000 79 AM2L-2412SH60-NZ 21.6-26.4 12 167 6000 82 AM2L-2415SH60-NZ 21.6-26.4 15 133 6000 80 Models Dual output Input Voltage Output Voltage Output Current Isolation Efficiency Model (V) (V) max (mA) (VDC) (%) AM2L-0505D-NZ 4.5-5.5 5 200 1000 82 AM2L-0512D-NZ 4.5-5.5 12 83 1000 84 AM2L-1215D-NZ 10.8-13.2 15 67 1000 85 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units 5 4.5-5.5 Voltage range 12 10.8-13.2 VDC 24 21.6-26.4 Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 sec 1000, 6000 VDC Capacitance 500VDC 10 pF Resistance 500Vdc >1000 MOhm Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy See Tolerance Graph 5 % 1000VDC Momentary 1 sec Short Circuit protection 6000VDC Continuous Short Circuit Restart Auto-Recovery Line voltage regulation For a 1% change of Vin 1.2 % Load voltage regulation (5 Vout) 12.8 Load voltage regulation (12 Vout) From 10% load to 100% load 6.8 % Load voltage regulation (15 Vout) 6.3 o Temperature coefficient At 100% load 0.03 %/ C Ripple & Noise* 20MHz Bandwidth 150 mV p-p Minimum Load Current** 10 % of Max www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.R 1 of 5 North America only Series AM2L-NZ 2 Watt DC-DC Converter *Test ripple & noise by Parallel Cable Method as described in Application Note Ripple and Noise Measurement of Brick & POL DC-DC Converters available on Aimtecs website www.aimtec.com **If the operating output current is less than 10% of maximum it is recommended to install a load resister in parallel with the load to ensure the actual load current meets the minimum load current requirement. General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load, nominal input 100 KHz o Operating temperature -40 to + 85 C o Storage temperature -55 to + 125 C o Maximum case temperature 100 C Cooling Free Air Convection Humidity 95 % RH Case material Plastic(UL94-V0) 1000VDC 2.1 Weight g 6000VDC 3.8 Single & Dual 1000VDC 0.70 x 0.70 x 0.24 inches 17.78 x 17.78 x 6.00 mm Dimensions (L x W x H) Single 6000VDC 0.94 x 0.79 x 0.32 inches 23.86 x 18.50 x 8.00mm MTBF >1,000, 000 hours (MIL-HDBK -217F, Ground Benign, t=+25C) o Maximum Soldering Temperature 1.5mm from case for 10 seconds 260 C Safety Specifications Parameters Agency approvals CE (for 6000VDC isolation models) Standards EN 60601-1-1 EN 60601-1-2 Pin Out Specifications 1000VDC 6000VDC Pin Single Dual Pin Single 1 -Vin - Vin 1 - V in 2 + Vin + Vin 2 No Pin 5 NC -Vout 3 No Pin 6 - Vout Common 4 No Pin 7 +Vout +Vout 5 No Pin 8 NC NC 6 No Pin 9 NC NC 7 NC 10 NC -Vout 8 NC 12 NC NC 9 +V out 13 NC NC 10 -V out 14 NC NC 11 No Pin 12 No Pin 13 No Pin 14 No Pin NOTE: On dual output models Pin 5 and Pin 10 are connected internally together. 15 No Pin Either Pin 5 or Pin 10, or both can be used as the -Vout NC: not connected 16 +V in www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.R 2 of 5 North America only