SOLUTIONS FOR RAPID PROTOTYPING Answering the Needs of Practicing Engineers Analog Devices participates in many vibrant hardware and software ecosystems, from Arduino to Pmod. Rapidly make your prototype and test your concepts. ADIs reference designs support many different applications and technologies, and include everything from hardware to embedded firmware that makes it easier for engineers to get their product concepts up and running fast. Arduino Shields Arduino shields are a popular hardware form factor that was first standardized by Arduino, and typically refer to being mechanically and electrically compatible with the Arduino Uno Rev 3 board. Many different FPGA, microprocessor, and DSP vendors provide plug and play connectivity into their development boards and environments using this form factor. Arduino shields provide analog and digital pins to configure devices and digitize signals coming from the real world. The digital communications 2 protocols supported by Arduino shields are SPI, I C, UART, PWM, and GPIO. All the below boards are compatible with either the EVAL-ADICUP360 or EVAL-ADICUP3029 and should work with any compatible Arduino form factor microcontroller platform. All software is open source and can be found on github.com/analogdevicesinc/. Water Quality Measurement System Dual Electrochemical Gas Detector X X Measure from 1 to 4 sensor channels Temperature compensation 2 X X Selectable SPI, I C, or UART communication Work with industry-standard gas sensors X X 10-pin JTAG/SWD connector for easy Programmable for a variety of gases programming X Visit analog.com/EVAL-CN0396-ARDZ X Visit analog.com/EVAL-CN0428-EBZ Water Turbidity Measurement System NDIR Thermopile-Based Gas Sensing Design X X 0 FTU to 1000 FTU measurement range Optimized for CO gas 2 X X 0.5 FTU system accuracy (up to 1000 FTU) Single supply X X Integrated ambient light rejection Visit analog.com/EVAL-CN0338-ARDZ X Visit analog.com/EVAL-CN0409-ARDZ Total Dissolved Solids Measurement System Electrochemical Toxic Gas Detection X X Temperature compensation Programmable for multiple other gases X X 1 s to 1 s measurement range Resolution down to 1 ppm X X Standard BNC conductivity probe connector Low power, single-supply operation X X Visit analog.com/EVAL-CN0411-ARDZ Visit analog.com/EVAL-CN0357-ARDZ Ultra Low Power Accelerometer with Display Mulitchannel Electrochemical Gas Detector X X Ultra low power sleep and wake-up modes 3- or 4-wire electrochemical gas sensors X X Programmable acceleration ranges Gas sensor diagnostics and life expectancy X X Board mounted LCD display Temperature and humidity compensation X X Visit analog.com/EVAL-ADXL362-ARDZ Visit analog.com/EVAL-CN0429-EBZ Micropower, 3-Axis, 200 g Digital Output MEMS Volatile Organic Compound Gas Detection X X Ultra low power sleep and wake-up modes Temperature and humidity compensation X X 200 g measurement range Can be used with multiple sensor types X X Adjustable high-pass filter Low power X X Visit analog.com/EVAL-ADXL372-ARDZ Visit analog.com/EVAL-CN0395-ARDZ Visit analog.comSolutions For Rapid Prototyping 2 Arduino Shields (Continued) Universal 4-Channel Thermocouple Dual RF RMS Power Detector Measurement System (Digital) X X Flexible 4-channel thermocouple system Measure forward and reverse rms power X X Cold junction compensation Good up to 7 GHz X X 24-bit digitization SMA input connector X X Visit analog.com/EVAL-CN0391-ARDZ Visit analog.com/DC2847A-KIT Universal 4-Channel Thermocouple RF/Microwave RMS Power Detector ( ) Measurement System Analog X X Flexible 4-channel thermocouple system 100 MHz to 40 GHz X X Cold junction compensation SMA input connector X X Visit analog.com/EVAL-CN0394-ARDZ Visit analog.com/DC2870A-KIT Ultra Low Power Light Recognition Measurement RF Gain and Phase Detector X Recognizes red, green, blue light sources X Low frequency to 2.7 GHz X Sensors are integrated on board X SMA input connector X Ultra low power X Visit analog.com/EVAL-AD8302-ARDZ X Visit analog.com/EVAL-CN0397-ARDZ Robust Closed-Loop Solenoid Control Design TruPWR RMS Detector X Overvoltage and undervoltage sensor control X 50 MHz to 9 GHz X Useful for on/off and proportional solenoids X SMA input connector X Closed-loop driver circuit for more X Visit analog.com/EVAL-ADL5902-ARDZ precise control X Visit analog.com/EVAL-CN0415-ARDZ Soil Moisture and pH Measurement System RS-485 Communications Shield X X Temperature compensation Isolated and nonisolated bus path X X Uses BNC standard pH probe connector Selectable as a master or a slave node X X Uses voltage output moisture probes Connect up to 32 boards together for network validation X Visit analog.com/EVAL-CN0398-ARDZ X Visit analog.com/EVAL-CN0416-ARDZ Precision Weigh Scale/Load Cell Design 4-Channel Analog Input PLC Module with HART X X 10 V, 4 mA to 20 mA input High gain, low noise X X Hardware open wire detection 4- or 6-wire load cell compatible X X HART compliant Full-scale sensor output up to 10 mV X X Visit analog.com/EVAL-CN0414-ARDZ Visit analog.com/EVAL-CN0216-ARDZ Programmable, 3-Channel LED Current Source 4-Channel Analog Output PLC Module with HART X X 1 A max current load per channel 10 V, 4 mA to 20 mA output X X Design to drive red, green, blue LEDs Programmable output values X X Isolated repeater for multiple LED banks HART compliant X X Visit analog.com/EVAL-CN0410-ARDZ Visit analog.com/EVAL-CN0418-ARDZ Pmod The Pmod (peripheral module)-compatible interface is an open standard by Digilent (a National Instruments Company) for peripherals used with FPGAs or microcontroller development boards. The modules are available from simple push buttons to more complex modules with analog-to-digital converters (ADCs), digital-to-analog converters (DACs), or LCD displays. These modules can be used with a variety of FPGA or microcontroller development boards from different vendors and support major digital communication 2 protocols such as SPI, I C, and UART. Pmod-compatible interfaces normally have additional software drivers and configuration is required. All software is open source and can be found on github.com/analogdevicesinc/. Low Power, Low Noise 3-Axis 0.25C Accurate Digital Temperature Sensor Digital Output Accelerometer X X 20-bit ADC resolution 16-bit digital temperature resolution 2 X X Programmable high- and low-pass digital filters I C Interface for up to 4 nodes on a single bus X X Low power (200 A in measurement mode Low power (700 W at 3.3 V normal ) ) and 21 A in standby mode mode, 7 W at 3.3 V in shutdown mode X X Visit analog.com/EVAL-ADXL355-PMDZ Visit analog.com/EVAL-ADT7420-PMDZ