MIQ24MS-2 Api Technologies

I/Q Mixer / Modulator Model MIQ24MS-2 Communications Band RF 1.9 to 4.2 GHz (1) Electrical Specifications : Specifications Model MIQ2xMS-2 Conditions Parameter RF (GHz) LO (GHz) IF (MHz) Min Typical Max SSB Conversion 2.0-4.2 2.0-4.2 DC-500 5.5 dB 7.0 dB (2) (3) loss: 6.0 dB 1.9-4.2 1.9-4.2 DC-500 7.5 dB LO Power Image Rejection Side- 26 dB 1.9-2.0 1.9-2.0 DC-500 18 dB 4 = +10 dBm (4) band Suppression: 32 dB 2.0-4.2 2.0-4.2 DC-500 20 dB Amplitude Match 1.9-4.2 1.9-4.2 DC-500 0.2 dB MIQ24MS-2 Phase Match 1.9-4.2 1.9-4.2 DC-500 2 deg Page 1 Isolation LO to RF: 42 dB 1.9-4.2 34 dB MIQ26MS-2 LO to I/Q: 30 dB 1.9-4.2 Page 2 RF to I/Q: 1.9-4.2 24 dB I/Q to RF: DC-500 40 dB MIQ27MS-2 Input 1 dB +6 dBm 1.9-4.2 1.9-4.2 DC-500 MIQ24 Page 3 Compression Point: Input Third Order 1.9-4.2 1.9-4.2 DC-500 +14 dBm MIQ24 Intercept Point: (5) LO Power: +10 dBm MIQ24 1.9-4.2 1.9-4.2 DC-500 Notes: 1. Specifications are guaranteed when tested as a downconverter in a 50 Ohm system at +25C with the nominal LO power. Specifications indicated as typical are not guaranteed. 2. Noise figure is typically within 0.5 dB of conversion loss for IF frequencies greater than 10 MHz. 3. Conversion loss typically degrades less than 0.5 dB at +100C and improves less than 0.5 dB at -55C. Conversion loss is the combined value. 4. Measured with an IF quadrature hybrid whose amplitude and phase errors are 0.5 dB and 3 degrees maximum. An IF quadrature hybrid is not included. 5. Usable LO drives are up to 2 dB below to 3 dB above nominal. Typical Performance at 25C 6. See Application notes M112, for aid in selecting the outline and for mounting and installation information. Outline: MSQ8 MIQ24MS-2 I 500 Q All dimensions are in inches and mm . REV Spectrum Microwave 2144 Franklin Drive N.E. Palm Bay, FL 32905 PH (888) 553-7531 Fax (888) 553-7532 4/19/18 www.SpectrumMicrowave.com Spectrum Microwave 2707 Black Lake Place Philadelphia, PA 19154 PH (215) 464-4000 Fax (215) 464-4001I/Q Mixer / Modulator Model MIQ26MS-2 Communications Band RF 1.9 to 4.2 GHz (1) Electrical Specifications : Specifications Model MIQ2xMS-2 Conditions Parameter RF (GHz) LO (GHz) IF (MHz) Min Typical Max SSB Conversion 2.2-4.2 2.2-4.2 DC-500 5.5 dB 7.0 dB (2) (3) loss: 6.0 dB 1.9-4.2 1.9-4.2 DC-500 9.0 dB LO Power Image Rejection Side- 26 dB 1.9-2.0 1.9-2.0 DC-500 18 dB 6 = +13 dBm (4) band Suppression: 32 dB 2.0-4.2 2.0-4.2 DC-500 20 dB MIQ24MS-2 Amplitude Match 1.9-4.2 1.9-4.2 DC-500 0.2 dB Page 1 Phase Match 1.9-4.2 1.9-4.2 DC-500 2 deg Isolation MIQ26MS-2 LO to RF: 42 dB 1.9-4.2 30 dB Page 2 LO to I/Q: 30 dB 1.9-4.2 RF to I/Q: 1.9-4.2 24 dB MIQ27MS-2 I/Q to RF: DC-500 40 dB Page 3 Input 1 dB +9 dBm 1.9-4.2 1.9-4.2 DC-500 MIQ26 Compression Point: Input Third Order 1.9-4.2 1.9-4.2 DC-500 +17 dBm MIQ26 Intercept Point: (5) LO Power: +13 dBm MIQ26 1.9-4.2 1.9-4.2 DC-500 Notes: 1. Specifications are guaranteed when tested as a downconverter in a 50 Ohm system at +25C with the nominal LO power. Specifications indicated as typical are not guaranteed. 2. Noise figure is typically within 0.5 dB of conversion loss for IF frequencies greater than 10 MHz. 3. Conversion loss typically degrades less than 0.5 dB at +100C and improves less than 0.5 dB at -55C. Conversion loss is the combined value. 4. Measured with an IF quadrature hybrid whose amplitude and phase errors are 0.5 dB and 3 degrees maximum. An IF quadrature hybrid is not included. 5. Usable LO drives are up to 2 dB below to 3 dB above nominal. Typical Performance at 25C 6. See Application notes M112, for aid in selecting the outline and for mounting and installation information. Outline: MSQ8 MIQ26MS-2 I 500 Q All dimensions are in inches and mm . REV Spectrum Microwave 2144 Franklin Drive N.E. Palm Bay, FL 32905 PH (888) 553-7531 Fax (888) 553-7532 4/19/18 www.SpectrumMicrowave.com Spectrum Microwave 2707 Black Lake Place Philadelphia, PA 19154 PH (215) 464-4000 Fax (215) 464-4001