EIRP305-T

EIRP305-T-1012qsg If redundancy is desired be sure to connect two separate power supplies by using the two DC inputs on the terminal Quick Start Guide blocks 4 Ports If only one power input is used the Fault LED will light (this is normal) RJ-45 ports: The RJ-45 ports auto-sense for 10 or 100 Mbps Elinx PoE Ethernet Switch device connections. The auto MDI/MDIX feature allows connections to switches, workstation and other equipment EIRP305-T without changing straight through or crossover cabling. The charts below show the cable pin assignments for straight through and crossover cables. MDI Cable Pinout Pin Signal 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- LED Chart 3 1. Auto MDI/MDI-x is MDI-X Cable Pinout supported. A straight Pin Signal through or cross-over LED Description 1 Rx+ cable may be used. 2 Rx- Green Power input 1 is active 2. 10/100 auto 3 Tx+ P1 negotiation and full/half- Off Power input 1 is inactive 6 Tx- duplex are supported. Green Power input 2 is active P2 PoE ports: The PoE ports on this switch follow Alternative A 1 Off Power input 2 is inactive standards and are limited to 15.4 Watts of power output per Items Included Red Power input 1 or 2 is inactive port. Ports 1 thru 4 support the IEEE802.3af standard and are classified as (PSE) power sourcing equipment, which Fault o Ethernet Switch Power input 1 and 2 are both Off means they can be used to power (PD) powered devices. o CD with Support Manual active, or no power is present o This Quick Start Guide The port is supplying power to Green o Panel Mount Bracket the connected device FWD (1 to 4) No device attached or no power Off Installation Complete 5 being supplied Green Connected to network 2 RJ-45 Hardware Installation 1. When the network cables are attached and power Flashing Networking is active Upper LED is applied, installation is complete. Off Not connected to network 2. The switch will automatically discover network 1. Select a mounting location and install the Yellow Full-duplex link devices, populate its MAC address table, and switch onto a piece of DIN rail or use the RJ-45 pass traffic to the appropriate ports. included panel mount brackets for wall or Flashing Collision occurs Lower LED panel mounting Off Half-duplex link or link down 2. Connect power to the switch 48 VDC X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Ethernet Modules category: Click to view products by B&B Electronics manufacturer: Other Similar products are found below : 1026937 1026932 M38510/00302BCA 70001610 70001634 850-15633 PD-AS-951/12-24 GX-OC1601 1402407 I210T1 I350T4V2 SBL2EX SL170115 GX-OD1612 CPTS-4R4E-R TDKEZW3 I350F2 I350F2BLK I350T2V2 V23993-USB1029A 100-POE4 105FX-ST 105TX-SL SEG305-T 70001992 70001993 708TX 854-19720 I350T4V2BLK I350T2V2BLK I210T1BLK PD-OUT/MBK/S SX-BR- 4600WAN2-US W4S105C X710DA4FHBLK I350T2V2BLK 936714 GX-ID1611 3G8F7-DRM21-E EKI-2525I-BE BCM53426A0KFSBG PCM-24R2GL-AE 96NIC-1G4P-PE-IN2 0.70001777 BCM53402A0KFSBG 105FXE-SC-15-POE PD-OUT/MBK/G 856-15410 X520QDA1 BCM84794A1KFSBG X520DA2OCP