MINI-BEAM ac-Voltage Series Installation Self-contained photoelectric sensors Guide Additional information on this product is immediately available online at www.bannerengineering.com/69942 View or download additional information, including excess gain curves, beam patterns and accessories. For further assistance, contact a Banner Engineering Applications Engineer at (763) 544-3164 or (888) 373-6767. Sensing Mode Range LED Model* Opposed Emitter SMA31E 3 m (10 ) Opposed Receiver SM2A31R Infrared Opposed Emitter - Long 880 nm SMA31EL Range 30 m (100 ) Opposed Receiver - Long SM2A31RL Range Opposed Emitter 0 to 300 mm (0 to 12 ) SMA31EPD Clear Plastic Detection Actual range varies, depending upon the light transmission properties ac mb-emitter w/cable.eps Opposed Receiver SM2A31RPD of the plastic material Clear Plastic Detection being sensed. Visible Red Emitters with Attached Cable Non-Polarized 650 nm 5 m (15 ) SM2A312LV Retroreflective bn Polarized 50 mm to 2 m SM2A312LVAG Retroreflective (2 to 7 ) 24-240V ac bu Extended-Range 10 mm to 3 m SM2A312LP Polarized Retroreflective (0.4 to 10 ) 380 mm (15 ) SM2A312D Diffuse All Other Cabled Models Infrared 300 mm (12 ) SM2A312DBZ 880 nm Divergent Diffuse 130 mm (5 ) SM2A312W bn 24-240V ac 16 mm (0.65 ) Focus SM2A312C bu Load Infrared 880 nm 43 mm (1.7 ) Focus SM2A312C2 ac mb-emitter w/qd.eps 16 mm (0.65 ) Focus SM2A312CV Convergent Visible Red Emitters with Quick Disconnect 650 nm SM2A312CV2 43 mm (1.7 ) Focus (3-Pin Micro-Style) Visible rd/bk 16 mm (0.65 ) Focus SM2A312CVG Green 24-240V ac 625 nm rd/wh Infrared gn SM2A312F 880 nm Glass Fiber Optic Range varies, depending SM2A312FV on sensing mode and Visible Red fiber optics used. 650 nm ac mb-no w/qd.epsAll Other Models Plastic Fiber Optic SM2A312FP with Quick Disconnect *S tandard 2 m (6.5 ) cable models are listed. (3-Pin Micro-Style) 9 m (30 ) cable: add suffix W/30 (e.g., SMA31E W/30). 3-pin Micro-style QD models: add suffix QD (e.g., SMA31EQD). rd/bk 24-240V ac rd/wh Load gn WARNING . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. NOTE: O utput Type for all models is SPST These sensors do NOT include the self-checking redundant circuitry necessary Solid-State 2-Wire. to allow their use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. Printed in USA 03/04 P/N 69942 rev. A Installation MINI-BEAM ac-Voltage Series Guide Dimensions Models with suffixes E, EL, EPD, R, RL, RPD, LV, LVAG, LP, D, C, C2, CV, CV2, and CVG Models with suffix FP Models with suffix DBZ and W 3.2 mm 12.2 mm (0.48 ) (0.13 ) 30.7 mm (1.21 ) 3 mm Clearance (2) 24.1 mm Bezel M18 x 1 x 15 mm Thread Fiber (0.95 ) (Mounting Nut Supplied) Optic Fitting 2 m (6.5 ) Cable 18.0 mm (0.71 ) 22.3 mm (0.88 ) Mounting Peg 19.1 mm ( 6.3 mm x 2.5 mm) (0.75 ) 51.8 mm 13.2 mm (0.52 ) 66.0 mm 54.8 mm 16.2 mm (2.04 ) (2.60 ) 27.4 mm (1.08 ) (2.16 ) (0.64 ) Models with suffix F and FV QD Models M18 x 1 x 19 mm Thread 12 mm Thread (Mounting Nut Supplied) Quick-disconnect 20.0 mm (0.79 ) Fiber Optic Fitting 69.9 mm (2.75 ) 31.2 mm (1.23 ) Sensor Features (shown with gasketed acrylic cover removed) Gain (Sensitivity) Adjustment Screw NOTES: Please observe proper ESD precautions Alignment Indicator Device (AID)* (grounding) when adjusting Gain pot or LO/DO switch. Light/Dark Operate Select Switch When turning the Light/Dark Operate Select Clockwise: Light Operate switch, be careful not to damage the small (outputs conduct when sensing tabs on the switch. light is received). Counterclockwise: Dark Operate (outputs conduct when sensing light is not received). *U.S. Patent no. 4356393 Banner Engineering Corp. Minneapolis, MN U.S.A. www.bannerengineering.com Tel: 763.544.3164 2 P/N 69942 rev. A