CA00652.00C01 Belden

code TECHNICAL DATASHEET CA00652 date 2014-01-30 Version 2 Cable assembly IP20 RJ45-RJ45 CAT6A page 1/2 4PR 1. Application: DataTuff CAT 6A Patchcord terminated with IP20 RJ45 on both sides for interconnection of data communication equipment such as Industrial Ethernet. 2. Description: Cable assembly consisting of BELDEN 74005PU: 4PR AWG26/7 CAT 7 F/STP PUR with both sides connectorised to a IP20 Industrial RJ45 CRIMP MALE connector and molded boot. 3. Codenumber: Belden Codenumbers: CA00652.00Cyy. The C represents the cable is coiled into a ring, a D represents a ring with length <1mtr The yy represents the length of the patchcord. Example: CA00652.00C10 = 74005PU IP20 RJ45 - IP20 RJ45 10m CA0065.00C1D5 = 74005PU IP20 RJ45 - IP20 RJ45 1.50 m 4. Mechanical and electrical properties: High voltage test : 1.5kV dc between contacts and contact to housing Wire continuity: tested each wire/contact and shield Operating temperature rating: -10 up to +60C Storage temperature rating: -40 up to +70C See table 2 for additional mechanical requirements. Test Title Agency Standard Insert Loss/ attenuation ISO/IEC 11801 or TIA/EIA-568-C.2 Clause 4.5 and 6.0 including 1.5 de-rating factor for stranded cables FEXT loss TIA/EIA-568-C.2 clause 6 NEXT(*) ISO/IEC 11801 A2 Return Loss ISO/IEC 11801 A2 Coupling attenuation ISO/IEC 24702 table 4 E class E channel 2 minimum Delay TIA/EIA-568-B.1 de-rated according to length based on 100 meter channel Delay Skew TIA/EIA-568-B.1 Note: Next requirement de-rated according ISO/IEC 11801 according to cable length Table 1: RJ- 45 Cordset Electrical/Transmission Requirements Belden Wire & Cable B.V. All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner code TECHNICAL DATASHEET CA00652 date 2014-01-30 Version 2 Cable assembly IP20 RJ45-RJ45 CAT6A page 2/2 4PR Test Title Test Conditions Pass Criteria Installation pull simulation With connector mated to a jack, Must Pass apply 20 pound load for 1 minutes Electrical/Transmission to cable in line with axis of requirements in chart connector at room temperature. above before, and after testing. No signs of degradation to cable, connector or cable to connector interface after load removed. Table 2: RJ45 IDC Industrial cordset Additional Mechanical Requirements 5.1 Connector RJ45 requirements: Mechanical IEC 60603-7-51 Electrical/ Transmission IEC 60603-7-51 and TIA 568C.2 Insertion life > 750 mating cycles (EIA/TIA-568-B.2 annex K.6.2.2.2) Contact resistance 20 m maximum Category 6 minimum 5.2 Wiring scheme: According EIA/TIA 568B TIA568B Pin assignment RJ45 Pin no. Colour of insulation 1 White/Orange 2 Orange 3 White/Green 4 Blue 5 White/Blue 6 Green 7 White/Brown 8 Brown 6. Change history: Revision Date By 1 26-11-2013 PBe 2 30-01-2014 LC Belden declares this product to be in compliance with the environmental regulations EU RoHS (Directive 2011/65/EU, 02 Jan. 2013) this is valid for all material produced after the RoHS compliant date for this product. Belden Wire & Cable B.V. All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner