PTL45-15O0-104A3

Features Carbonelement Red,orange,green,amberandwhiteLEDcolors Centerdetentoption Assortmentofresistancetapers Varioustravel lengths Variousleversizes PTL Series Slide Potentiometer w/LED Product Dimensions Electrical Characteristics Standard Resistance Range 20 mm Length of Travel Lever ........................1K ohms to 1 megohm 35.0 0.5 Length Standard Resistance Tolerance....20 % (1.378 .020) 9.0 0.5 End Resistance 10.0 31.0 0.2 (.354 .020) (1.220 .008) 20 mm Travel ............... 10 ohms max. (.394) 2.8 27.0 30 mm Travel ............... 20 ohms max. (.110) 15.0 (1.063) 45 mm Travel ............... 20 ohms max. (.591) 1 60 mm Travel ............... 30 ohms max. 19.0 100 mm Travel ............. 30 ohms max. (.748) Insulation Resistance 250 VDC 0.4 M2 X 2 PLCS............................ 100 megohms min. (.016) Dielectric Withstanding Voltage 20.0 0.5 3.0 MM ..............................................300 VAC (0.787 .020) DIMENSIONS: 5.5 (.118) (INCHES) Standard Taper.................. Linear, Audio (.217) 5.5 0.1 6.0 0.1 Power Rating - Linear (.217 .004) (.236 .004) 2.05 0.1 20 mm Travel ....................... 0.05 watt 6.6 1.0 0.1 (.081 .004) 30 mm Travel ......................... 0.1 watt (.260) (.039 .004) 45 mm Travel ..................... 0.125 watt LED L 0.5 60 mm Travel ......................... 0.2 watt 0.5 (L .020) MOUNTING 100 mm Travel ....................... 0.2 watt (.020) SURFACE Power Rating - Audio 20 mm Travel ..................... 0.025 watt 7.0 0.5 30 mm Travel ....................... 0.05 watt 0.4 0.6 3.5 0.5 (.276 .020) (.016) 45 mm Travel ....................... 0.06 watt (.024) (.138 .020) 60 mm Travel ......................... 0.1 watt 100 mm Travel ....................... 0.1 watt Slider Noise .......................200 mV max. Environmental Characteristics Mounting Hole Detail Operational Life ................15,000 cycles TR Shift .....................................15 % 7.5 0.1 Operating Temperature Range (.295 .004) 30.0 0.1 ..................................-10 C to +55 C 2.5 0.1 (1.181 .004) (.098 .004) 2 Resistance to Solder Heat..............5 % 1 3 L Moisture Sensitivity Level.....................1 HOLES E B ESD Classification (HBM)................. N/A 1.1 +0.2/-0 (.043 +.008/-0) DIA. 6 PLCS. Mechanical Characteristics Mechanical Travel.........Length 0.5 mm Standard Resistance Table Schematic Operating Force...............30 gf to 250 gf Center Detent Force........20 gf to 200 gf Resistance Resistance 2 Stop Strength.......................... 5 kgf min. (Ohms) Code 1,000 102 Shaft Axial Force .................... 5 kgf min. R1 1 3 2,000 202 Shaft Wobble...2(2 x L/20) mm p-p max. 5,000 502 Soldering Condition 10,000 103 20,000 203 Manual ........... 300 C 5 C for 3 sec. 50,000 503 Wave .............. 260 C 5 C for 5 sec. 100,000 104 Wash ..................... Not recommended 200,000 204 500,000 504 1,000,000 105 WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specications are subject to change without notice. Users should verify actual device performance in their specic applications. The products described herein and this document are subject to specic legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. *RoHS COMPLIANTApplications Mixingconsoles Drummachines Keyboardsandsynthesizers Equalizers PTL Series Slide Potentiometer w/LED Product Dimensions 30 mm Length of Travel 45 mm Length of Travel 60.0 0.5 45.0 0.5 (1.772 .020) (2.362 .020) 9.0 0.5 41.0 0.2 56.0 0.2 (.354 .020) 9.0 0.5 (2.205 .008) (1.614 .008) 2.8 (.354 .020) 37.0 52.0 (.110) 2.8 (2.047) (1.457) (.110) 1 1 0.4 M2 X 2 PLCS. (.016) 0.4 M2 X 2 PLCS. (.016) 30.0 0.5 3.0 (1.181 .020) 45.0 0.5 5.5 (.118) 3.0 (1.772 .020) (.217) 5.5 0.1 (.118) 5.5 6.0 0.1 (.217 .004) 5.5 0.1 (.217) (.236 .004) (.217 .004) 6.6 6.0 0.1 1.0 0.1 (.236 .004) (.260) (.039 .004) 6.6 LED (.260) 1.0 0.1 L 0.5 (.039 .004) 0.5 (L .020) LED L 0.5 MOUNTING (.020) SURFACE (L .020) 0.5 MOUNTING (.020) SURFACE 7.0 0.5 0.4 3.5 0.5 (.276 .020) (.016) 7.0 0.5 0.4 (.138 .020) 3.5 0.5 (.276 .020) (.016) (.138 .020) 2.05 0.1 (.081 .004) 2.05 0.1 (.081 .004) 0.6 (.024) 0.6 (.024) Mounting Hole Detail Mounting Hole Detail 7.5 0.1 7.5 0.1 (.295 .004) 40.0 0.1 (.295 .004) 2.5 0.1 55.0 0.1 (1.575 .004) 2.5 0.1 (2.165 .004) (.098 .004) 2 (.098 .004) 1 3 2 L 1 3 HOLES E B L E B HOLES 1.1 +0.2/-0 1.1 +0.2/-0 (.043 +.008/-0) (.043 +.008/-0) DIA. 6 PLCS. DIA. 6 PLCS. MM DIMENSIONS: (INCHES) Specications are subject to change without notice. Users should verify actual device performance in their specic applications. The products described herein and this document are subject to specic legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.