HCPL-4503-300E Broadcom

HCNW4502/3 HCPL-0452/0453/4502/4503 Single Channel, High Speed Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Description Features 15 kV/s minimum common mode transient These diode-transistor optoc oup lers use an insulating immunity at V = 1500 V layer between a LED and an integrated photodetector to CM provide elec trical in sula tion between input and out put. High speed: 1 Mb/s Separate connections for the photodiode bias and out- TTL compatible put-transistor collector increase the speed up to a hun- Available in 8-Pin DIP, SO-8, widebody packages dred times that of a conventional phototransistor coupler Open collector output by reduc ing the base-collector capacitance. Guaranteed performance from temperature: These single channel optocouplers are available in 0C to 70C 8-Pin DIP , SO-8 and Widebody package configurations. Safety approval UL Recognized 3750 V for 1 minute (5000 V The HCPL-4502/4503 and HCNW4502/4503 are designed rms rms for 1 minute for HCNW and Option 020 devices) for high speed TTL/TTL applications. A standard 16 mA TTL per UL1577 sink current through the input LED will provide enough CSA Approved output current for 1 TTL load and a 5.6 k pull-up resistor. IEC/EN/DIN EN 60747-5-5 Approved CTR for these devices is 19% minimum at I = 16 mA. F V = 630 V peak for HCPL-4503 060 IORM Functional Diagram V = 1414 V peak for HCNW devices IORM Dual channel version available (4534/0534) NC V 1 8 CC MIL-PRF-38534 hermetic version available TRUTH TABLE (55XX/65XX/4N55) (POSITIVE LOGIC) ANODE 7 NC 2 LED V o ON LOW Applications CATHODE 6 V 3 o OFF HIGH High voltage insulation NC GND 4 5 Video signal isolation Power transistor isolation in motor drives A 0.1 F bypass capacitor must be connected between pins 5 and 8. Line receivers Feedback element in switched mode power supplies High speed logic ground isolation TTL/TTL, TTL/CMOS, TTL/LSTTL Replaces pulse transformers Replaces slow phototransistor isolators Analog signal ground isolation CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.The HCPL-4502, HCPL-0452, and HCNW4502 provide the Schematic electrical and switching performance of the 6N136, HCPL- I CC 8 0501, and HCNW136 with increased ESD protection. V CC The HCPL-4503, HCPL-0453, and HCNW4503 are similar to I the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers F 2 ANODE but have increased common mode transient immunity of + 15 kV/s minimum at V = 1500 V guaranteed. V CM F I O 6 V O CATHODE 3 5 SHIELD GND HCPL-4503/0453 HCNW4503 Selection Guide Widebody Minimum CMR 8-Pin DIP (300 Mil) Small-Outline SO-8 (400 Mil) Hermetic Current Single Dual Single Dual Single Single and dV/dt V Transfer Channel Channel Channel Channel Channel Dual Channel CM (V/s) (V) Ratio (%) Package Package* Package Package* Package Packages* 10 19 HCPL-4502 HCPL-0452 HCNW4502 15,000 1500 19 HCPL-4503 HCPL-4534 HCPL-0453 HCPL-0534 HCNW4503 1,000 10 9 HCPL-55XX HCPL-65XX 4N55 *Technical data for these products are on separate Avago publications. 2