HLMA-Qx00, HLMA-Px00 HLMT-Px00 and HLMT-Qx00
Subminiature High Performance AlInGaP LED Lamps
Data Sheet
SunPower Series
HLMA-PF00, HLMA-PG00, HLMA-PH00, HLMA-PL00, HLMA-QF00, HLMA-QG00, HLMA-QH00,
HLMA-QL00, HLMT-PG00, HLMT-PH00, HLMT-PL00, HLMT-QG00, HLMT-QH00, HLMT-QL00
Description Features
Subminiature fl at top package
Flat Top Package
Ideal for backlighting and light piping applications
The HLMX-PXXX fl at top lamps use an untinted, nondif-
Subminiature dome package
fused, truncated lens to provide a wide radiation pattern
Nondiff used dome for high brightness
that is neces sary for use in backlighting applica tions. The
Wide range of drive currents
fl at top lamps are also ideal for use as emitters in light
Colors: 590 nm Amber, 605 nm Orange, 615 nm Red-
pipe applications.
dish-Orange, 622/626 nm Red, and 635 nm Red
Dome Packages
Ideal for space limited applications
Axial leads
The HLMX-QXXX dome lamps use an untinted, nondif-
fused lens to provide a high luminous inten sity within a
Available with lead confi gurations for surface mount
narrow radiation pattern.
and through hole PC board mounting
Lead Confi gurations
Technology
All of these devices are made by encapsulating LED chips
on axial lead frames to form molded epoxy submini-
These subminiature solid state lamps utilize one of the
ature lamp packages. A variety of package confi guration
two newly devel oped aluminum indium gallium phos-
options is available. These include special surface mount
phide (AlInGaP) LED technologies. The HLMT-Devices
lead confi gura tions, gull wing, yoke lead, or Z-bend. Right
are especially eff ective in very bright ambient lighting
angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm
condi tions. The colors 590 nm amber, 605 nm orange,
(0.200 inch) center spacing are available for through hole
615 nm reddish-orange, 622/626 nm red, and 635 nm red
mounting. For more infor mation refer to Standard SMT
are available with viewing angles of 15 for the domed
and Through Hole Lead Bend Options for Subminiature
devices and 125 for the fl at top devices.
LED Lamps data sheet.Device Selection Guide
Typ. I Package Viewing Package
d V
1
Part Number (nm) (mcd) Description Angle 2 / Outline
2
HLMA-QL00 590 500 Domed, 15 B
HLMT-QL00 590 1000 Nondiff used,
HLMA-QJ00 605 500 Untinted
HLMA-QH00 615 500
HLMT-QH00 615 800
HLMA-QG00 626 500
HLMT-QG00 622 1000
HLMA-QF00 635 500
HLMA-PL00 590 75 Flat Top, 125 A
HLMT-PL00 590 150 Nondiff used,
HLMA-PJ00 605 75 Untinted
HLMA-PH00 615 75
HLMT-PH00 615 120
HLMA-PG00 626 75
HLMT-PG00 622 150
HLMA-PF00 635 75
Absolute Maximum Ratings at T = 25C
A
Parameter HLMA-xxxx HLMT-xxxx Unit
[2]
Peak Forward Current 100 100 mA
[1,2]
Average Forward Current (I = 100 mA) 30 30 mA
PEAK
[3,5,6]
DC Forward Current 50 50 mA
Power Dissipation 120 130 mW
Reverse Voltage (I = 100 A) 5 V
R
[5]
Transient Forward Current (10 s Pulse) 500 mA
Operating Temperature Range 40 to +100 C
Storage Temperature Range 55 to +100 C
LED Junction Temperature 110 C
Lead Soldering Temperature [1.6 mm (0.063 in.) from body] 260C for 5 seconds
SMT Refl ow Soldering Temperature 260C for 20 seconds
Notes:
1. Maximum I at f = 1 kHz.
AVG
2. Refer to Figure 5 to establish pulsed operating conditions.
3. Derate linearly as shown in Figure 4.
4. The transient peak current is the maximum non-recurring peak current these devices can withstand without damaging the LED die and wire
bonds. Operation at currents above Absolute Maximum Peak Forward Current is not recommended.
5. Drive currents between 10 mA and 30 mA are recommended for best long term performance.
6. Operation at currents below 5 mA is not recommended, please contact your Avago sales representative.
2