Transceiver for Digital Signals Type G 3440 4443 4-channel monostable transceiver 2 opto-isolated voltage inputs: 10 to 265 VAC/DC 2 SPST relay outputs Load 2 x 5 A/250 VAC H4-housing For mounting on DIN-rail (EN 50022) LED-indications for supply, Dupline carrier, inputs and outputs AC or DC power supply Channel coding by GAP 1605 Product Descrip tion Ordering Key G 3440 4443 024 Dupline transceiver with 2 and 2 SPST relay outputs. Type: Dupline in-puts for AC/DC voltages H4-housing Transceiver No. of channels Input/output type Power supply Type Selection Supply Ordering no. 4 channels 2 x voltage input 2 x SPST relay outputs 24 VAC G 3440 4443 024 115 VAC G 3440 4443 115 230 VAC G 3440 4443 230 15 to 30 VDC G 3440 4443 824 Input Spec i fi cations Output Spec ifi ca tions Inputs 2 voltage-type Output 2 SPST relays Isolated in groups of 1 x 2 Isolated in groups of 2 x 1 Input voltage V 10 to 265 VAC/DC BB Contact ratings (AgCdO) (micro gap) Frequency range on AC 45 to 400 Hz Resistive loads AC 1 5 A/250 VAC (1250 VA) Input voltage for signal 0 1 VAC/DC DC 1 0.25 A/250 VDC (62 W) Input voltage for signal 1 10 VAC/DC or 5 A/25 VDC (125 W) Input current for signal 1 Typ. 10 mA (V 10-18 VDC) BB Inductive loads AC 15 2.5 A/230 VAC lower at other input voltages DC 13 5 A/24 VDC Input current limiter Yes 6 Mechanical lifetime 30 x 10 operations Inrush current 450 mA ( V = 265 VDC) BB Electrical lifetime Operating time for signal 1 1 pulse train + 3 ms 6 (at max load) AC 1 2 x 10 operations Operating time for signal 0 1 pulse train + 50 ms Operating frequency 7200 operations/h Cable length 25 m Dielectric voltage Dielectric voltage Outputs - Dupline 4 kVAC (rms) Inputs - Dupline 4 kVAC (rms) Response time 1 pulse train Inputs - Outputs 4 kVAC (rms) Specifications are subject to change without notice (23.10.2014) 1 G 3440 4443 Supply Spec ifi ca tions Power supply AC types Overvoltage cat. III (IEC 60664) Rated operational voltage Rated operational voltage through term. 21 & 22 824 15 to 30 VDC (ripple includ ed) through term. 21 & 22 230 230 VAC 15% (IEC 60038) Ripple 3 V 115 115 VAC 15% (IEC 60038) Reverse-polarity protection Yes 024 24 VAC 15% Rated operational power 1.5 W Frequency 45 to 65 Hz Power dissipation 5.5 W Voltage interruption 40 ms Inrush current 1 A Rated operational power Typ. 4 VA Rated impulse withstand Power dissipation 8 W voltage 800 V Rated impulse withstand Dielectric voltage voltage 230 4 kV Supply - Dupline 200 VAC (rms) 115 2.5 kV Supply - Inputs 4 kVAC (rms) 024 800 V Supply - Outputs 4 kVAC (rms) Dielectric voltage AC types as input supply source Supply - Dupline 4 kVAC (rms) Source voltage V out DD Supply - Inputs 4 kVAC (rms) through term. 3 & 4 12 VDC Supply - Outputs 4 kVAC (rms) Source current 20 mA Power supply DC type Overvoltage cat. III (IEC Short-circuit protection Yes 60664) Dielectric voltage Supply output - Dupline 200 VAC (rms) Cable length 25 m Mode of Operation General Spec i fi ca tions Each input and each out - The table below shows the Power ON delay Typ. 2 s put may be cod ed indi- rela tion between the inputs/ Power OFF delay 1 s vid u al ly by means of the out puts of the G 3440 4443 code program-mer GAP and the In/Out-markings on Output OFF delay 1605. For the gen er al pro- the GAP 1605. upon loss of Dupline carrier 20 ms ce dure of coding, please Indication for refer to the respec tive data Supply ON LED, green Output/input connections sheet. In order to allocate a Dupline carrier LED, yellow Input 1: terminals 6 & 7 code address to the inputs/ Input/Output LED, red (one per in-/output) Input 2: terminals 6 & 8 out puts of the G 3440 4443, Environment Output 1: terminals 25 & 26 it is neces sary to set the Degree of protection IP 20 Output 2: terminals 27 & 28 GAP 1605 in sin gle chan-nel Pollution degree 3 (IEC 60664) address ing mode. Operating temperature -20 to +50C (-4 to +122F) Storage temperature -50 to +85C (-58 to +185F) GAP 1605 G 3440 4443 When a volt age (10 to 265 Humidity (non-condensing) 20 to 80% VAC/DC) is applied to input 1 In/out 1 Input 1 (terminal 7), the G 3440 4443 Mechanical resist ance In/out 2 Input 2 transmits on the Dupline Shock 15 G (11 ms) In/out 3 Not used channel cod ed for input 1. Vibration 2 G (6 to 55 Hz) In/out 4 Not used Out put 1 turns on when a Terminals Screwterminals In/out 5 Output 1 trans mit ter coded to the Tightening torque 0.8 Nm In/out 6 Output 2 same Dupline address as In/out 7 Not used Dimensions H4-Housing output 1 becomes acti vat ed. In/out 8 Not used Weight 250 g 2 Specifications are subject to change without notice (23.10.2014)