Dupline DeviceNet Gateway Du line Type G 3891 0050 Fieldbus Installationbus Built-in Dupline channel generator DeviceNet slave DeviceNet communication speed of up to 500 kBaud Read/control of 128 Dupline inputs/outputs through DeviceNet Split-I/O mode selectable (128 inputs and 128 outputs) Support of 3 1/2 digit BCD and AnaLink analog formats All Dupline formats (except 8 bit binary multiplexed) available on the DeviceNet network For mounting on DIN-rail (EN 50 022) LED indicators for supply, Dupline carrier and fault AC power supply Product Description Ordering Key G 3891 0050 230 Dupline Channel Generator interface cards, etc. from vari- Type: Dupline with the function of a ous suppliers). Several H8-Housing DeviceNet slave. This means Dupline gateways can be Type no. that the 128 Dupline I/Os connected to the same Supply can be read/controlled by DeviceNet network. DeviceNet masters (PLCs, PC Type Selection Supply Ordering no. 115/230 VAC G 3891 0050 Input/Output Specifications DeviceNet Adjustments Pin assignment V- Pin 1 1 x 16 pos. rotary switch No. of Dupline channels CAN-L Pin 2 8 .. 128 in steps of 8 SHIELD Pin 3 DIP-switch 1 Dupline mode (Normal/Split I/O) CAN-H Pin 4 DIP-switch 2 Dupline data transfer mode V+ Pin 5 DIP-switch 3 Analog input Baudrate Switch settings DIP-switch 4 Analog output Cable length (Thick cable) 100 m 500 kBaud CE-marking Yes 200 m 250 kBaud 1200 m 125 kBaud Update time (128 digital I/O) Typ. 200 s at 560 kBaud Typ. 1.6 ms at 125 kBaud Dielectric voltage DeviceNet Dupline 4 kVAC (rms) EDS-file Dupline Output voltage 8.2 V Output current 100 mA Short-circuit protection Yes All channels ON detector Yes Output impedance 15 Sequence time 8 digital I/O 15.2 ms 128 digital I/O 132.3 ms AnaLink value update time 8 signals 3.9 s 128 signals 33.8 s Specifications are subject to change without notice (28.09.99) 1 Dupline is a registered trademark. A product of the CARLO GAVAZZI GroupG 3891 0050 Du line Fieldbus Installationbus General Specifications Supply Specifications Power supply Overvoltage cat. III (IEC 60664) Power ON delay < 2.5 s until start of Rated operational voltage Dupline carrier. through term. 21, 22, 23 & 24 See wiring diagram < 40 s until correct reading 230 230 VAC 15% (IEC 60038) of AnaLink values 115 115 VAC 15% (IEC 60038) Indication for Frequency 45 to 65 Hz Supply ON LED, green Rated operational power 11 VA Dupline carrier LED, yellow Rated impulse withstand Fault LED, red voltage 230 4 kV Environment 115 2.5 kV Degree of protection IP 20 Dielectric voltage Pollution degree 3 (IEC 60664) Supply - Dupline 4 kVAC (rms) Operating temperature 0 to +50C (+32 to +122F) Supply - RS 485 4 kVAC (rms) Storage temperature -20 to +85C (-4 to +185F) Humidity (non-condensing) 20 to 80% RH Mechanical resistance Shock 15 G (11 ms) Vibration 2 G (6 to 55 Hz) Dimensions H8-housing Material (see Technical information) Weight 540 g Wiring Diagrams S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Dupline No Baud Address Settings Channels 17 VA ON Network Status Module Status 1 2 3 4 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 115V 115V P NP N Power supply Power supply SUPPLY 230 VAC 115 VAC Mode of Operation The Dupline DeviceNet 1x16 position rotary-switch output(s) coded for B5 will received on DeviceNet. Gateway is a Dupline Chan- for selecting Number of also be activated. Conse- nel generator with a function Dupline Channels in the quently, a Dupline output 1x DIP-switch for selection of of a DeviceNet slave. This range 8..128 (in steps of 8). can either be activated through analog data. means that the 128 Dupline The selected letter indicates the output-data received on In OFF position only Digital I/Os can be read/controlled the last channel group avail- DeviceNet or by an active In/Out data are transferred. by DeviceNet masters like able on Dupline . If e.g. H is Dupline input coded for the To enable analog data-I/O PLCs and PC interface- selected, the 64 channels in same Dupline address. handling this DIP-switch cards from many different groups A..H will be available. In Split I/O mode, the must be ON. suppliers. Several Dupline Dupline inputs and Dupline Gateways can be connected 1x DIP-switch for selection of outputs are treated indepen- 1x DIP-switch for selection of to the same network and Dupline Operation Mode. dently by the channel gener- Analog input operation mode. operate together with other In Normal mode, Dupline ator. If e.g. and input coded When OFF the analog input DeviceNet modules like operates as a peer-to-peer for B5 is activated, the Gate- data are read as AnaLink. operatorpanels, MMIs I/O system where the channel way will make the informa- Each channel from C1 to P8 modules etc. generator automatically es- tion available on DeviceNet are read as 8 bit analog data. tablishes a connection be- (like in normal mode), but it When ON the analog input Configuration switches tween Dupline inputs and will not automatically activate data are considered as 3 1/2 The unit is equipped with Dupline outputs which are the Dupline output(s) coded digit multiplexed data. The the following configuration coded to the same Dupline to B5. The Dupline outputs multiplex-control (Synchro- switches. (See also switch address. If e.g. an input cod- are controlled exclusively nization) are automatically settings) ed for B5 is activated, the through the output data set to operate on channels 2 Specifications are subject to change without notice (28.09.99) Dupline is a registered trademark. A product of the CARLO GAVAZZI Group V- CAN-L SHIELD CAN-H V+