T t y f p e r p e a g p Switching Power Supply Type SPD 90W DIN rail mounting Installation on DIN Rail 7.5 or 15mm Short circuit protection PFC standard High efficiency Power ready output LED indicator for DC power ON LED indicator for DC low Model specific to meet UL 1310 class 2 UL, cUL listed and TUV/CE approved Product De scrip tion Ordering Key SP D 24 90 1 B The Switching power supplies and compact dimensions and Model SPD series are specially performance are a must. Mounting ( D = Din rail ) designed to be used in all This version is specifically Output voltage automation application where developed to meet UL1310 Output power the installation is on a DIN rail class 2. Input type Optional features Approvals Input type: 1= single phase Rheinland Product Safety Optional Features Description Code Standard screw terminal Nil Plug-in connectors B Output performances Rated output Output DC ON LED (VDC) DC LO LED (VDC) Output Voltage Trim Range Typical Thereshold at startup Thereshold after startup Model Voltage Power Current (A) Efficiency (VDC) (W) Min. VDC Max. VDC Min. Max. Min. Max. SPD2490 24 92 3.8 22.5 24.5 17.6 19.4 17.0 19.4 85% Output data Output voltage accuracy -0 +1% max (factory adjusted) Transient recovery time 300s Line regulation 0.5% Ripple and noise 50mVpp Load regulation Hold up Time Vi = 115VAC 25ms Hold up time Vi = 230VAC 30ms Non parallel model 1% Parallel model 5% Minimum load 0% Temp. coefficient 0.3% / C Parallel Operation No Input data Rated input voltage 115/230 autoselect Rated input current 2.0 / 0.8A Voltage range Frequency range 47- 63 Hz AC in, 115 90 - 132VAC Inrush current AC in, 230 186 - 264VAC Vi= 115VAC 24A DC in 210 - 370VDC Vi= 230VAC 48A P.F.C. 0.7 1 Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network. - 1410 t p r a r u o a v B e dSwitching Power Supply Type SPD 90W DIN rail mounting Controls and Protections 1) Input Fuse T3.15/250VAC internal Power ready Threshold at start up 17.6 - 19.4 Overvoltage Protection 102 - 106% (contact closed) Output Short Circuit Current limited Contact rating at 60VDC 0.3A Rated Overload Protection 102 - 108% Insulation 500VDC 1) Fuse not replaceable by user General data ( nominal line, full load, 25C ) Ambient temperature -25C to 71C Switching frequency 80kHz Derating (>60C to +71C) 2.5% / C MTBF (MIL-HDBK-217F) 480.000h Ambient humidity 20 to 95%RH Case material Metal (powder painted aluminium) Storage -25C to +85C Dimensions L x W x D 125 x 63.5 x 126 Protection degree IP20 Weight 920g Cooling Free air convection Approvals and EMC Insulation voltage I / O 3.000VAC min CE EN50081-1 EN55022 class B Insulation resistance 100M min EN61000-3-2 UL / cUL UL508 listed, UL60950-1 EN61000-3-3 Recognized EN61000-6-2 UL1310 class 2 EN61000-6-3 TUV EN60950-1 EN55024 Block diagrams L Fuse Vo + Inrush Current Line P.F.C. Smoothing Switching Limiter and Rectifier Filter Circuit Circuit Device Current Rectifier Detection Vo - N Y PWM Controller Reference & Opto - Error Amp. Vout isolation ADJ. Opto - Over Voltage isolation Detection DCON (Green LED) Output Level Detection DCLOW (Red LED) RDY 1) (Relay Contact) 1) for SPD24 models Pin assignement and front controls Pin No. Designation Description 1RDY DC OK, relay normally open contact 2RDY DC OK, relay normally open contact 3+ Positive output terminal 4+ Positive output terminal 5- Negative output terminal 6- Negative output terminal 7GND Ground terminal to minimise High frequency emissions 8L Phase input ( no polarity with DC input ) 9N Neutral input ( no polarity with DC input ) DC ON DC output ready LED DC LO DC low indicator LED Vout ADJ. Trimmer for fine output voltage adjustment 1410 - Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network.