SOM040100 Celduc

S/CON/SOM040100/B/18/12/14 Page 1/5 UK MOSFET BASED SOM040100 DC SOLID-STATE RELAY Latest MOSFET technology generation. Ultra low on-state resistance. Low output leakage current. Low control current consumption. Built-in overvoltage protection Reverse protected triggered control input to avoid linear control risks Control voltage range 3.5-32VDC No radiated or conducted disturbances Max. permanent 60VDC output voltage Touch protected housing IP20 Max. load current 40ADC with heatsink Control input In & case / Out Dimensions Load voltage range Load current range Connections Weight voltage range Insulation (WxHxD) Up to 40A 45 x 58.5 x 30 5-60VDC 3.5-32VDC 2.5kV Screw terminals 80g (with heatsink) HIGH SIDE WIRING DIAGRAM LOW SIDE WIRING DIAGRAM Fig. 1 Fig. 2 (Load connected to -) (Load connected to +) See Instruction See Instruction sheet to select sheet to select the the right right protective protective components components The red paths The red paths (C1/D2) must be (C1/D2) must as short as be as short as possible possible Fig. 3 INTERNAL DIAGRAM Proud to serve you celduc Data given at Tambient=25C and subject to modification without previous notice r e l a i s celduc S/CON/SOM040100/C/18/12/14 r e l a i s Page 2/5 UK CONTROL INPUT CHARACTERISTICS CHARACTERISTIC LABEL VALUE INFO. Nom. Control voltage Ucnom 12-24VDC Min. Control current Icmin 35mADC -100A/C typical ON=3.3V Control voltage range Uc 3.5 32VDC Control current consumption Ic 32 35mADC (for control voltage range) See fig. 5 typical OFF= 2.6V Releasing control voltage Ucoffmax 1VDC Max. reverse control voltage -Ucmax 32VDC -Icmax<100A Input impedance Rin Current limitation See fig. 5 POWER OUTPUT CHARACTERISTICS CHARACTERISTIC LABEL VALUE INFO. Nominal voltage Uenom 48VDC Voltage range Ut Ue 5-60VDC Non-repetitive peak voltage Utp 100V Transient voltage suppressor Overvoltage protection D1 56V (1500W/1ms) Max reverse voltage drop (internal Ie=80A -Ut 1.3V Uc=0 diode at OFF state) Resistive Motor See fig. 7 Maximum nominal currents Ie max (limits) 40A Please contact us Non-repetitive peak overload Id max 320A See fig. 8 current Min. load current Iemin 5mA Utmax Tjmax Max. leakage current Ielk max 3mA Iemax Tjmax Max. on-state resistance RDSon 30mOhms Typ. output capacitance Cout 0.7nF Junction/case thermal resistance Rthjc 0.9K/W per power element Built-in heatsink thermal Rthra 10K/W Tra=75C resistance vertically mounted Heatsink thermal time constant Tthra 10 minutes Tra=75C Control inputs/power outputs Uimp 2.5kV insulation voltage Inputs/case insulation voltage Uimp 2.5kV Outputs/case insulation voltage Uimp 2.5kV Isolation resistance Rio 1G Isolation capacitance Cio <8pF Maximum junction temperature Tjmax 175C Storage ambient temperature Tstg -40->+100C Operating ambient temperature Tamb -25->+90C See fig. 7 Max. case temperature Tc 100C PROTECTION CHARACTERISTICS Leakage current (Ielk) vs DC voltage (Ut) Absolute limits Ielk / Ie Uto Utp 1 0,8 0.75 t max 0,6 (Uto Ut max) Ie 0,4 P (protection ) 1W max 0,2 (Uto Ut max) Ie t 0 1 T 0 1020 3040 50 6070 8090 100 Ut (V) Utmax Utp (=Uemax) Ielk : Leakage current of the relay Utmax : Max. nominal voltage of the relay t : Overvoltage duration Ie : User load nominal current Uto : Possible overvoltage above Utmax T: Time between 2 overvoltage Utp : Relay max. non repetitive peak voltage Utn = Ue : User DC power supply voltage PROTECTION POWER CIRCUIT INPUT CIRCUIT