Type PPC, -55 C to + 125 C, Ultra-Thin Polymer Aluminum Electrolytic Capacitor High Ripple and DC Holdup Rated for 125 C, PPC combines the advantages of aluminum electrolytic and aluminum polymer technology. These capacitors have the ultra- low ESR characteristics of conductive aluminum polymer capacitors in a 1mm thin package. With high capacitance and high ripple current per volume, applications for 125 C polymer capacitors include DC/DC converters, tablets, telecommunications, thin displays, and variety of industrial power conversion. Highlights - +125 C, Up to 2,000 Hours Load Life - Low Leakage Current - Very Low ESR and High Ripple Current - Just 1mm thin Specifications Temperature Range -55 C to + 125 C Rated Voltage 6.3 Vdc 24 Vdc (see table for derating) Capacitance 8000 F - 20,000 F Capacitance Tolerance 20% at 120 Hz and 25 C Leakage Current (at 25C) I Max = 0.005CV after 2 minute charge I = leakage current in Amps C = rated capacitance in F V = rated DC Working voltage in Volts Low Temperature Characteristics (at 120 Hz) Z(-55 C)/Z(+25 C): 3.0 Insulation Nylon Operating Temperature -55 C to + 125 C Terminal Material Tin plated copper (0.010) Precautions Do not bend or strike capacitor body Ripple Current Frequency Multiplier Ripple Multipliers for Ambient Temperature (No Heatsink) Ta (C) 45 55 65 75 85 95 105 Ripple Current Multiplier 2.22 1.96 1.68 1.37 1.00 0.73 0.48 Ripple Multipliers for Air Velocity (No Heatsink) Air Velocity (m/s) 0.25 1 2.5 5 Ripple Current Multiplier 1.00 1.36 1.52 1.66 Ripple Multipliers for Frequency Frequency (Hz) 50 60 120 360 1000 5000 20000 Ripple Current Multiplier 0.77 0.81 1.00 1.16 1.24 1.20 1.12 Ripple Multipliers for Case Ambient Temperature (Heatsinked to Bus) Ta (C) 45 55 65 75 85 95 105 One Side 2.96 2.66 2.32 1.96 1.58 1.08 0.60 Both Sides 3.00 3.00 3.00 2.77 2.24 1.52 0.85 Mechanical Shock MILSTD202, Method 213, Condition I, 100 G peak, 6mS, Sawtooth, 18 Shocks CDM Cornell Dubilier 140 Technology Place Liberty, SC 29657 Phone: (864)843-2277 Fax: (864)843-3800 Type PPC, -55 C to + 125 C, Ultra-Thin Polymer Aluminum Electrolytic Capacitor Vibration Test Level The specimens, while deenergized or operating under the load conditions specified, shall be subjected to the vibration amplitude, frequency range, and duration specified for each case size. Level = 10g Amplitude The specimens shall be subjected to a simple harmonic motion having an amplitude of either 0.06-inch double amplitude (maximum total excursion) or peak level specified above, whichever is less. The tolerance on vibration amplitude shall be 10 percent. Frequency Range The vibration frequency shall be varied logarithmically between the approxi- mate limits of 10 to 2,000 Hz. Sweep Time and Duration The entire frequency range of 10 to 2,000 Hz and return to 10 Hz shall be traversed in 20 minutes. This cycle shall be performed 12 times in each of three mutually perpendicular directions (total of 36 times), so that the motion shall be applied for a total period of approximately 12 hours. Interruptions are permitted provided the requirements for rate of change and test duration are met. Mounting Recommended mounting with 3M double sided VHB tape appropriate for mounting surfaces and to ensure the entire capacitor surface is held rigid. Altitude 10,000 Feet Endurance Life Test Apply the maximum rated voltage for 2,000 hrs at +85 C with full rated ripple current. After the test, return the capacitor to room temperature for 24 hours and then test. C at 120Hz/+25 C: 20% of the initial ESR at 120Hz/+25 C: ESR 200% of the initial DCL after 2 minute charge/+25 C: 0.005CV Shelf Life Test Subject the capacitor to 1000 hrs at +125 C without voltage. After the test, return the capacitor to room temperature for 24 hours and then test. C at 120Hz/+25 C: 20% of the initial ESR at 120Hz/+25 C: ESR 200% of the initial DCL after 2 minute charge/+25 C: 0.005CV Moisture Resistance Test MIL-STD-202, method 106. After the test, return the capacitor to room temperature for 24 hours and then test. C at 120Hz/+25 C: 20% of the initial ESR at 120Hz/+25 C: ESR 200% of the initial DCL after 2 minute charge/+25 C: 0.005CV Charge/Discharge Test Charge to rated Vdc and discharge to 0 Vdc, 100,000 cycles at 0.1 Hz, through a 0.22 resistor 25C. After the test, return the capacitor to room temperature or 24 hours and then test. C at 120Hz/+25 C: 20% of the initial ESR at 120Hz/+25 C: ESR 200% of the initial DCL after 2 minute charge/+25 C: 0.005CV RoHS Compliant CDM Cornell Dubilier 140 Technology Place Liberty, SC 29657 Phone: (864)843-2277 Fax: (864)843-3800