Dcmind Brush motor Series Data sheet 89 830 012 89 830 3,7 103 maxi 4 x M5 at 90, depth 10mm and 40 mm diameter 4 x holes diam 3.65 at 90, depth 8mm and 48 mm 4 x M5 at 90, depth 7mm and 40 mm diameter diameter General characteristics 24 Motor characteristics at (1) Vdc Winding parameters (1) At no load - A Torque constant mNm/A 63,6 +-10% Speed rpm 3 600 +-10% Volts/(rad/s) 0,064 +-10% Constant electromotive force Current A 0,23 V / Krpm 6,66 +-10% EMC (55022) class B Resistance Ohms 1,4 +-10% Life (2) h 20 000 Inductance mH 1,7 At max efficiency - B Start voltage Volts 0,6 Speed rpm 3 240 +-10% Current demagnetization (magnets at 150 C) A 60 Torque (4) mNm 111 Power output W 38 Generic parameters 1,97 Current A Motor for direct current supply 80 Efficiency % Output shaft with ball bearings B (20mm from front face) 150 EMC (55022) class Max. Radial force N Life (2) h 10 000 Max. axial force(5) N 100 CEI60068-2-1/2 At nominal load - C Temperature range C -30 / 70 +-10% Speed rpm 3 000 Storage temperature C -40 / 100 (1min 2mA 50Hz) CEI60335 Torque (4) mNm 180 Dielectric Vdc 500 Power output W 57 Motor insulation CEI60085 class E (120C) Current A 3,1 Enameled wire insulation class F (155C) CEI60068-2-58 Efficiency % 77 Salt spray severity 2 EMC (55022) class B Degree of protection CEI60529 IP 65 Life (2) h 5 000 EMC Others Electrostatic Discharge CEI61000-4-2 level 3 Starting torque mNm 1 080 Electrical fast transsient / burst test CEI61000-4-4 level 3 Starting current A 17,2 Surge test CEI61000-4-5 level 2 W 102 class Max. output power Radiated emission B Motor parameters (1) rpm 10 000 Allowed speed max Approvals mNm 180 1004 Rated torque Designed in accordance with UL ms 1,2 2002/95/CE Electrical time constant ROHS ms 13 Mechanical time constant EC mNm/rpm 0,3 Factor torque / speed Designed for medical machines using the standard EN60601-1 7 Dry friction mNm Values without tolerences, are average production values. mNm/krpm 1,5 Viscous friction 380 (1) Cold motor, 20 C ambient temperature Rotor inertia gcm (2) Continuous cycle, one direction Thermal Resistance /W 6 (3) Continuously rated torque, zero radial and axial loads Stator poles 2 (4) Max torque for continuous operation at 20 C, decrease this value for higher ambient temperature Collector blades 12 Cogging torque mNm 9 (5) Pinion or pulley fitting are done at the Crouzet factory, before final assembly. Weight (g) g 1 200 Noise level dBA 35 Curves 4 000 20 120 90 Performance / Motor curves (1) 3 500 80 Voltage supply Vdc 24 100 70 3 000 15 Output data 80 60 2 500 50 ABCD 2 000 10 60 3 600 3 240 3 000 0 40 Speed rpm 1 500 40 30 0 111 180 1 080 Torque (4) mNm 1 000 5 20 Current A 0,2 2,0 3,1 17,2 20 500 10 -38 57 - Power output W 0 0 0 0 -80 77 - Efficiency % 0 0,2 0,4 0,6 0,8 1 1,2 0 0,2 0,4 0,6 0,8 1 1,2 Torque (Nm) Torque (Nm) B (max efficiency) C (nominal) Specifications subject to change without notice. Updated february 29, 2012. Crouzet Automatismes 2 rue du Docteur Abel BP59 www.crouzet.com 26902 Valence CEDEX 9 France Speed (rpm) Current (A) Power (W) Efficiency (%) Series 89 830X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for AC, DC & Servo Motors category: Click to view products by Crouzet manufacturer: Other Similar products are found below : 79207644 805470B40040MY 80807028 808070Y01125Z 808550Y00049Z 823055C10001MWY 82520405 82664024 82802504 R88MK10030H M4E068-EC03-01 M4E068-CF01-01 79265119 80510503 805470A40040MY 805470B40020MY 80627003 808070Y00250Y 808070Y83.33Y 823055A20001MW 825140A40010MP 825290C43.75MX 82714023 82800003 82830009 82810017 R88M-K90010F-S2 R88M-K1K030H-S2 89830012 82840003 82840004 82869011 82524021 82862202 82869006 82861013 80803009 80547015 82862205 R88M-K40030T-B 80527006 82330514 81021118 82524004 89800008 82867009 82662564 82662515 82600041 82524008