296UD504B1N CTS

Series 296 Data SheetData Sheet Electrocomponents Rotary Potentiometer Commercial 12mm Diameter Carbon Composition Rotary Potentiometer Features Miniature 12mm size Low cost Snap-in bracket for PC board mounting Detent available Insulated shaft available RoHS compliant Electrical and Mechanical Specifications Stop Strength Resistance Range 500 ohms through 1 Megohms 5.76 kg-cm minimum (VR without detent) 3 kg-cm minimum (VR with detent) Resistance Tolerance 30%, 20%, 10% Mounting Information P.C. board mounting Power Rating Type: Shaft parallel to P.C. board 0.15 watts 50C Type: Shaft vertical to P.C. board Dielectric Strength Type: Same as except hook terminals 500 VDC for 1 minute Detent Maximum Operating Voltage Detent 50% rotation 350 VDC Push-Pull strength on shaft Insulation Resistance 8 kg for 10 seconds 100 Megohms minimum 250 VDC Rotational life Rotational Angle 10K cycles Mechanical angle: 300 Effective angle: 280 Operating temperature -10C ~ 80C Rotational Torque 20 216 gf-cm Solder Heat Resistance 260C for 5 seconds 1 - 2 2009 CTS Corporation. All rights reserved. Information subject to change. 2/06/09 www.ctscorp.com CTS ElectrocomponentsP.C. Board XM 296RE/ HM 296RE Molded Shaft, Shaft Parallel to 6.3 0.8 6.3 0.8 L L .248 .248 .031 .031 12.5 1.00 1.00 .492 .040 .040 7.200.10 7.200.10 .283.004 .283.004 6.4 .252 3.000.10 6.000.15 .118.004 .236.006 16.4 .646 10.00 1.600.08 .394 TYP.(2) .063.003 2.100.10 TYP.(2) .083.004 4.0 3.750.05 3.750.05 .157 .148.002 .148.002 1.8 1.8 +0.10 .071 .071 1.30 -0.00 TYP.(3) 1.90.1 .051 +.004 1.90.1 0.90.1 -.000 .075.04 TYP.(3) .075.04 .035.004 13.0 3.00.1 3.00.1 .512 .118.04 .118.04 4.1 4.1 15.2 .161 .161 .598 DIMENSION AND TOLERANCE UNLESS OTHERWISE SPECIFIED 0.3 0.13 X Terminal Style H Terminal Style .X (1 PLACE) : .XX (2 PLACE) : .012 .005 mm DIMENSION: ANGLE : 5 inch UM 296RE Molded Shaft, Shaft Perpendicular to P.C. Board 10.000.10 0.8 8.7 .394.004 L .342 1.600.08 .031 TYP.(2) 12.5 .063.003 1.00 .492 CENT040 3.750.05 5.500.05 2.54 .148.002 .217.002 6.4 .100 .252 3.750.05 5.500.05 CENT. 6.000.15 .148.002 .217.002 .236.006 +0.10 +0.15 10.000.1 1.30 2.70 -0.00 -0.00 .394.004 TYP.(3) +.006 +.004 .051 .106 -.000 -.000 0.40.0.03 .016.01 Ordering Information 296 X B 252 B 2 N TERMINAL STYLE RESISTANCE CODE RESIST TOL DETENT X PC EXAMPLES A 10% N NO DETENT U PC FORMED CODE RESISTANCE B 20% C CENTER DETENT TO REAR 501 500 OHMS H HOOK C 30% 102 1K 252 2.5K SHAFTS AVAILABLE 502 5K (ALL SHAFTS .236 Dia.(6.0mm) except - Diameter is .240 (6 .1mm) 103 10K LENGTH BEYOND 253 25K COVER TRIM TAPER 503 50K A .640 (16.3mm) FLATTED .472 X.177 (12X4.5mm) 104 100K 1 LINEAR B .840 (21.3mm) FLATTED .472 X.177 (12X4.5mm) 2 10% AUD C1.031 (26.2mm) FLATTED .472 X.177 (12X4.5mm) 3 10% CCW AUD D .540 (13.7mm) KNURLED .287 X 18T (7.3mmX18T) E .265 ( 6.7mm) FLATTED .218 X .204 (5.5X5.2mm) F .640 (16.3mm) FLATTED .276 X .177 (7X4.5mm) G .717 (18.2mm) FLATTED .276 X .177 (7X4.5mm) H1.035 (26.3mm) FLATTED .276 X .177 (7X4.5mm) 2/06/09 2 - 2 2009 CTS Corporation. All rights reserved. Information subject to change. www.ctscorp.com CTS Electrocomponents