o f N d o n r a t l h n i A e Additional Resources: Product Page date 07/22/2015 page 1 of 19 SERIES: PSE-3000 DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY FEATURES redundant (N+1) operation up to 3000 W continuous power blind mate connections for hot-swap 80 PLUS Platinum Efficiency constant power (CP) mode PoE output isolation (1500 Vrms to ground) 3 harmonic correction to EN61000-3-2, Class A high power density - 33.48 W/in TM DROOP current sharing PMBus communication for monitoring & single I/O connector for AC input, DC output control & signals dual fan forced cooling with speed control remote on/off control front to back (-F) and back to front (-B) power good signal airflow versions optional 19 four slot power shelf power factor correction 3.3 Vdc (2A) standby voltage C US 4 output output output ripple efficiency MODEL 2,3 1 voltage current power and noise max max max typ (Vdc) (A) (W) (mVp-p) (%) PSE-3000-48-F 48 62.5 3000 480 94 PSE-3000-48-B 48 62.5 3000 480 94 PSE-3000-54-F 54 55.5 3000 540 94 PSE-3000-54-B 54 55.5 3000 540 94 Notes: 1. Measured at 20 MHz bandwidth at an oscilloscope jack on the output with 0.1 F ceramic and 10 F aluminum electrolyitc capacitors. 2. At 90~180 Vac input, maximum of 1500 W. 3. At 180~264 Vac input, maximum of 3000 W. 4. At 230 Vac input, 3000 W. Meets 80 PLUS platinum efficiency requirements. 5. All specifications measured at: Ta=25C and 220 Vac input voltage unless otherwise specified. PART NUMBER KEY PSE-3000 - XX - X - CXX Base Number Reserved for Custom Configurations Output Voltage Airflow Direction: F = AC input connector to DC output connector B = DC output connector to AC input connector cui.com m h e R r i V c a U DISCONTINUED , T I n c .Additional Resources: Product Page CUI Inc SERIES: PSE-3000 DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 07/22/2015 page 2 of 19 INPUT parameter conditions/description min typ max units voltage 90 264 Vac frequency 47 63 Hz at 90 Vac, 1500 W 20.2 Arms current at 180 Vac, full load 18.5 Arms at 115 Vac, cold start 20 A inrush current at 230 Vac, cold start 40 A leakage current 1.5 mArms power factor correction at 230 Vac, full load 0.99 ( ) OUTPUT - V1 MAIN OUTPUT parameter conditions/description min typ max units line regulation 3 % load regulation 3 % load capacitance 30,000 F 50% step load, 1A/s slew rate, recovery to 1% transient response 3 % within 1 ms start-up time 5 s hold-up time at 230 Vac, full load 12 ms remote sense between both output terminals 0.5 V current share accuracy (Droop) over 25% to 100% load 10 % AC OK: green to indicate AC above the lower limit that is required to sustain normal operation LED indicator DC OK: green to indicate module in normal operating condition ( ) OUTPUT - V2 STANDBY OUTPUT parameter conditions/description min typ max units output voltage 3.3 Vdc output current 0 2 A 1 ripple and noise 33 mVp-p line regulation 5 % load regulation 5 % load capacitance 1000 F 50% step load, 1A/s slew rate, recovery to 1% transient response 3 % within 1 ms start-up time 5 s Notes: 1. Measured at 20 MHz bandwidth at an oscilloscope jack on the output with 0.1 F ceramic and 10 F aluminum electrolyitc capacitors. PROTECTIONS parameter conditions/description min typ max units V1: latch off 60 Vdc over voltage protection V2: latch off 110 120 % V1: constant current inception 62.5 A over current protection V2: hiccup 2.6 A over temperature protection at full load, auto recovery 55 C cui.com DISCONTINUED