TECHNICAL DATASHEET CliQ II DIN Rail Power Supply 48 V 480 W 1 Phase / DRP048V480W1B Highlights & Features Universal AC input voltage range Power will not de-rate for the entire input voltage range Power Boost of 150% for 5 seconds and 200% for 2 seconds Full corrosion resistant aluminium casing Conforms to harmonic current IEC/EN 61000-3-2, Class A Extreme low temperature cold start at -40C Conformal coating on PCBAs to protect against common dust and chemical pollutants Hazardous Locations approval to ATEX and Class I, Div 2 (DRP048V480W1BA) Certified according to IEC/EN/UL 62368-1 Safety Standards CB Certified for worldwide use Model Number: DRP048V480W1B Unit Weight: 1.37 kg (3.02 lb) Dimensions (L x W x D): 121 x 144 x 118.6 mm (4.76 x 5.67 x 4.67 inch) General Description The CliQ II DIN rail power supply series from one of the worlds leading power supply companies, Delta Electronics Group, offers output voltage of 48 V. These products are encased in rugged yet lightweight full aluminium body that can withstand shock and vibration according to IEC 60068-2 standard. The DRP048V480W1B can operate over a wide temperature range of -25C to +75C. The series of single phase products also features universal AC input voltage range from 85 Vac to 264 Vac and the power will not de-rate throughout the entire range. Another great feature is the conformal coating on the PCBA which allows selected models to be certified to ATEX and Class I, Div 2 for use in hazardous locations. The design conforms to harmonic current emission IEC/EN 61000-3-2, Class A. Model Information CliQ II DIN Rail Power Supply Model Number Input Voltage Range Rated Output Voltage Rated Output Current DRP048V480W1B 85-264 Vac (120-375 Vdc) 48 Vdc 10.0 A Model Numbering P 048V DR 480W 1 B DIN Rail Power Supply Output Voltage Output Power Single Phase CliQ II Series A - Metal Case, with Class I, Div 2 N - Metal Case, without Class I, Div 2 All parameters are specified at 25C ambient and AC input unless otherwise indicated. 1 www.DeltaPSU.com (September 2021, Rev. 08) TECHNICAL DATASHEET CliQ II DIN Rail Power Supply 48 V 480 W 1 Phase / DRP048V480W1B Specifications Input Ratings / Characteristics Nominal Input Voltage 100-240 Vac Input Voltage Range 85-264 Vac Nominal Input Frequency 50-60 Hz Input Frequency Range 47-63 Hz DC Input Voltage Range* 120-375 Vdc Input Current < 5.00 A 115 Vac, < 3.00 A 230 Vac Efficiency at 100% Load > 91.0% 115 Vac, > 93.0% 230 Vac Max Power Dissipation 0% load < 5 W 115 Vac & 230 Vac 100% load < 46.5 W 115 Vac, < 34.5 W 230 Vac Max Inrush Current < 35 A 115 Vac & 230 Vac Power Factor at 100% Load > 0.96 115 Vac, > 0.90 230 Vac Leakage Current < 3 mA 240 Vac *Fulfills test conditions for DC input. Safety approval for DC input can be obtained upon request. Output Ratings / Characteristics** Nominal Output Voltage 48 Vdc Factory Set Point Tolerance 48 Vdc 1% Output Voltage Adjustment Range 48-56 Vdc Output Current 10.0 A (continuously operating at 48 V) 15.0 A (Power Boost for 5 seconds at 48 V, refer to the details in the Functions section) Output Power 480 W (continuously operating at 48 V) 720 W (Power Boost for 5 seconds at 48 V, refer to the details in the Functions section) Line Regulation < 0.5% ( 85-264 Vac input, 100% load) Load Regulation < 1.0% ( 85-264 Vac input, 0-100% load) PARD*** (20 MHz) < 200 mVpp Rise Time < 350 ms nominal input (100% load) Start-up Time < 1,500 ms nominal input (100% load) Hold-up Time > 20 ms 115 Vac & 230 Vac (100% load) Dynamic Response 2% 85-264 Vac input, 10-90% load (Overshoot & Undershoot O/P Voltage) (Slew Rate: 0.1 A/s, 50% duty cycle 5 Hz to 1 KHz) Start-up with Capacitive Loads 10,000 F Max **For power de-rating from > 50C to 75C, see power de-rating on page 3. *** PARD is measured with an AC coupling mode, 5 cm wires, and in parallel with 0.1 F ceramic capacitor & 47 F electrolytic capacitor. All parameters are specified at 25C ambient and AC input unless otherwise indicated. 2 www.DeltaPSU.com (September 2021, Rev. 08)