SPECIAL PURPOSE HAND CRIMP TOOL 1716P-1 DATASHEET THIS HAND TOOL MUST NOT BE USED IN ANY POWERED SEE REVERSE SIDE FOR IMPORTANT INFORMATION CONCERNING PRES AS DEFINED BY OSHA CFR 1910.211 (46) LIMITED WARRAN TY, AND LIMITATION OF LIABILITY. GENERAL INFORMATION * Model number of tool refers to both the positioner and tool frame as a combined unit. TOOL IN OPEN .,.J POSITION * The tool has a double action ratchet. ,,..--- / ----- - .,,., ,..,,. Note that the tool cannot be opened FIXED without completing cycle. - - OOL IN CLOSED POSITION ER - POSITION ----- SPECIFICATIONS GAGING: WIRE SIZE: r GO .073 10-12* NO-GO .078 I 1 Contacts: M39029/56-527 M39029/58-528 M39029/106-618 M39029/107-624 DATAPLATE M39029/117-637 M39029/118-649 M39029/117-643 M39029/118-655 M39029/121-668 M39029/122-675 B *Recommended to use MS3348-10-12 Crimp Bushing with Size 12 Wire (See AS39029/112 for more info) , - , CRIMPING INSTRUCTIONS 1. With tool in open position, insert contact assembly through indenter opening COLOR CODE and into positioner. 2. Squeeze handles together until ratchet BLUE BLUE BLUE releases. Handles will return to open position. Remove crimped contact assembly. GAGING INSTRUCTIONS NO-G GAGING G GAGING Operate tool to fully closed position. Maintain firm hand pressure on the tool handles. InsertNO-G Operate tool to fully closed position. Maintain firm gage end as shown. TheNO-G gage may partially hand pressure on the tool handles. InsertG gage enter the indenter opening, but must not pass end os shown. Gage must pass freely between completely through the opening. indenter tips. CAUTION DO NOT CRIMP GAGE GREEN GREENGNO G INDENTER G415 DANIELS MANUFACTURING CORP., 526 THORPE ROAD, ORLANDO, FL 32824, USA, PHONE 407 /855-6161, FAX 407 /855-6884 COPYRIGHT 2016 DANIELS MANUFACTURING CORP., USA. WWW.DMCTOOLS.COM E-MAIL: DMCOOMCTOOLS.COM ALL RIGHTS RESERVED AUGUST 2016 REV. E 1716P-1-DS DI...,. DANIELS MANUFACTURING - - ,,,...,CORPORATION DATA SHEET CARE OF TOOL It is a good practice to keep indenter tips free of residual color band deposits and other debris. A small wire brush may be used for this purpose. We strongly recommend that you: 1. DO NOT immerse tools in cleaning solution. 2. DO NOT spray oil into tool to lubricate. 3. DO NOT attempt to disassemble tool or make repairs. This 1s a precision hand crimp tool and should be handled as such. DMC offers complete refurbishing and recalibration services. DMC specially engineers and manufactures complete tool kits to satisfy individual customer requirements, such as total aircraft support, general shop maintenance or production, on board ship and vehicle service, etc. LIMITATION OF LIABILITY DANIELS MANUFACTURING CORPORATION IS NOT LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE OR KIND RESULTING FROM THE USE, OR MISUSE, OF ANY OF ITS PRODUCTS. OWNERS AND USERS OF DMC PRODUCTS ASSUME FULL RESPONSIBILITY FOR INSTRUCTING THEIR EMPLOYEES IN THE PROPER AND SAFE USE OF SUCH PRODUCTS. LIMITED WARRANTY DMC (Daniels Manufacturing Corporation) warrants each new product sold by it to be free from defects in material and workmanship under normal use and service. DMC s obligation under this warranty is limited to the free correction or, at DMc s option, the refund of the purchase price of any such product which proves defective in normal service within ninety (90) days ofter delivery to the first user, provided that the product is returned to DMC with oil transportation charges prepaid and which shall appear to DMC s satisfaction, after DMC s inspection, to hove been defective in material or workmanship, it being understood that DMC products are not consumer products. This warranty shall not cover any damage to any product which, in the opinion of DMC, was caused by normal wear, misuse, improper operation, tampering, neglect or accident. This warranty is in lieu of oil other warranties express or implied. No warranty, express or implied, is mode or authorized to be mode or assumed with respect to products of Daniels Manufacturing Corporation other than those herein set forth.