REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED 93-02-19 M. A. Frye A Add device types 03 06. Add U packages. Changes to Table I and Figures 1, 3, and 4. Editorial changes throughout. 93-10-01 M. A. Frye B Changes in accordance with NOR 5962-R239-93 07-02-15 Joseph Rodenbeck C Boilerplate update, part of 5 year review. ksr THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Gary L. Gross DEFENSE SUPPLY CENTER COLUMBUS CHECKED BY COLUMBUS, OHIO 43218-3990 STANDARD 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89817 01 X A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 1/ Circuit function Access time 01 32K x 8 UVEPROM 55 ns 02 32K x 8 UVEPROM 45 ns 03 32K x 8 UVEPROM 35 ns 04 32K x 8 UVEPROM 55 ns 05 32K x 8 UVEPROM 45 ns 06 32K x 8 UVEPROM 35 ns 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP4-T28 or CDIP3-T28 28 Dual-in-line 2/ Y GDFP2-F28 28 Flat pack 2/ Z CQCC1-N32 32 Rectangular leadless chip carrier 2/ U GDIP1-T28 or CDIP2-T28 28 Dual-in-line 2/ 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range---------------------------------------------------------------- -0.5 V dc to +7.0 V dc DC voltage applied to outputs in high Z state --------------------------------- -0.5 V dc to +7.0 V dc DC input voltage---------------------------------------------------------------------- -3.0 V dc to +7.0 V dc DC program voltage ----------------------------------------------------------------- 13.0 V dc Maximum power dissipation (P ) ------------------------------------------------- 1 .0 W 3/ D Lead temperature (soldering, 10 seconds maximum)----------------------- +260 C Thermal resistance, junction-to-case ( ) ------------------------------------- See MIL-STD-1835 JC Junction temperature (T)---------------------------------------------------------- +175 C J Storage temperature range-------------------------------------------------------- -65 C to +150C Temperature under bias ------------------------------------------------------------ -55 C to +125C Endurance------------------------------------------------------------------------------ 10 cycles/byte minimum Data Retention ------------------------------------------------------------------------ 10 years/minimum 1.4 Recommended operating conditions. Supply voltage (V )--------------------------------------------------------------- 4.5 V dc to 5.5 V dc CC Ground voltage (GND) ------------------------------------------------------------ 0.0 V DC Input high voltage (V )------------------------------------------------------------ 2.0 V dc minimum IH Input Low voltage (V ) ------------------------------------------------------------ 0.8 V dc maximum IL Case operating temperature range (T)-------------------------------------- -55C to +125C C 1/ Generic numbers are listed on the Standardized Military Drawing Source Approval Bulletin and will also be listed in MIL-BUL-103. 2/ Lid shall be transparent to permit ultraviolet light erasure. 3/ Must withstand the added P due to short circuit test (e.g., I ). D OS SIZE STANDARD 5962-89817 A MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 C 2 DSCC FORM 2234 APR 97