SPECIFICATIONS AND ORDERING INFORMATION C2/C3 - SERIES 0.82 / 1.2 WIDE 0.25 AMP 28 VDC The C2/C3 Series offers an 8 position and a 12 position vertical P.C. board mountable design. Standard designs utilize a 30 index angle and polyester insulation. C SPECIFICATIONS ELECTRICAL MECHANICAL Current and Voltage Rating: Make and break resistive load Materials and Finishes: All parts utilize non-corrosive materials 0.25 amp 28 VDC 0.1 amp 125 VAC. as standard. Current Carrying Capacity: 6 amps. Terminals and Contacts: Brass with silver plate as standard. Dielectric Strength: 1,000 VAC between current carrying parts and Insulation: Polyester. ground. Index: Dual-ball, hill and valley. Contact Resistance: Average initial 30 milliohms. Index Life: 25,000 cycles minimum. Insulation Resistance: In excess of 10,000 megohms. Index Torque: Switches have lowest practical torque consistent with crisp detenting and smooth, reliable operation. Index Angles: Positive 30 standard, 60, and 90 available. Hardware: Mounting nut and lockwasher are shipped assembled. Index Stops: Fixed standard, adjustable, or continuous available. Stop Strength: 8 in. lbs. minimum. STANDARD PART NUMBER C3 - 12 PIN CONSTRUCTION SWITCHES - 30 INDEXING C2 - 8 PIN CONSTRUCTION SWITCHES - 30 INDEXING ADJUSTABLE STOPS SET 2 POS. - P.C. TERMINALS ADJUSTABLE STOPS SET 2 POS. - P.C. TERMINALS ACTIVE POLES/ NO. OF SHORTING NON- FIG. ACTIVE POLES/ NO. OF SHORTING NON- FIG. POLES POSITIONS DECK DECKS SHORTING POLES POSITIONS DECK DECKS SHORTING * * 01 02-08 1 1 C2P0108S - A C2P0108N - A CD 01 02-12 1 1 C3P0112S - A C3P0112N - A CA 02 02-08 1 2 C2P0208S - A C2P0208N - A CD 02 02-12 1 2 C3P0212S - A C3P0212N - A CA 02 02-04 2 1 C2P0204S - A C2P0204N - A CI 02 02-06 2 1 C3P0206S - A C3P0206N - A CH 03 02-08 1 3 C2P0308S - A C2P0308N - A CD 03 02-04 3 1 C3P0304S - A C3P0304N - A CK 04 02-04 2 2 C2P0404S - A C2P0404N - A CI 03 02-12 1 3 C3P0312S - A C3P0312N - A CA 04 02-08 1 4 C2P0408S - A C2P0408N - A CD 04 02-06 2 2 C3P0406S - A C3P0406N - A CH 05 02-08 1 5 C2P0508S - A C2P0508N - A CD 04 02-12 1 4 C3P0412S - A C3P0412N - A CA 06 02-04 2 3 C2P0604S - A C2P0604N - A CI 06 02-04 3 2 C3P0604S - A C3P0604N - A CK * FIGURES ARE SHOWN ON PAGE 55. C2 - DIMENSIONS - 8 PIN DESIGN C2P - STANDARD 8PIN PER DECK ARRANGEMENT A 195 1/4 DIAMETER SHAFTS ARE AVAILABLE. CONTACT FACTORY. 2010 Yonkers Road Raleigh, NC 27604 ELECTRONIC PRODUCTS UNIT OF ELECTRO SWITCH CORP. Telephone: (888) ROTARYS or (919) 833-0707 8 Fax: (800) 909-9171 or (919) 833-8016ADDITIONAL OPTIONS AND C2/C3 - SERIES ORDERING INFORMATION How to Order Additional Options: 2 DIGIT INSULATION TOTAL ACTIVE CONTACT TERMINAL INDEX STOP SHAFT/ SHAFT SERIES TYPE POLES POSITIONS TYPE TYPE ANGLE TYPE BUSHING FLAT C2 P-POLYESTER 01 - MIN. 08 - MAX 30 N- NON 30 F- FIXED 04 - MAX 60 SHORTING 60 C- CONT. 03 - MAX 90 S- SHORTING 90 A- ADJ. SEE SEE CHART CHART C C3 P-POLYESTER 01 - MIN. 12 - MAX 30 N- NON 06 - MAX 60 SHORTING 04 - MAX 90 S - SHORTING CUSTOMERS SPECIFIED ORDER NUMBER FOR STANDARD OPTIONS ADDITIONAL OPTIONS P (SPECIFY) (SPECIFY) (SPECIFY) (SPECIFY) (SPECIFY) (SPECIFY) (SPECIFY) SHAFT AND FLAT OPTIONS PRINTED CIRCUIT BOARD PATTERN C2 C3 8PIN DECK 12PIN DECK SHAFT AS VIEWED WITH NON-TURN LUG AT 9 O CLOCK AND SHAFT IN EXTREME CCW POSITION AND STRUT BOLTS ORIENTED VERTICALLY. NOTES: 1. The standard spacing for the 1/8 dia. shaft from the first row of terminals to the mounting surface is .390 in. 2. The standard spacing for the 1/4 dia. shaft from the first U W Y Z row of terminals to the mounting surface is .481 in. C3 - DIMENSIONS - 12 PIN DESIGN C3P - STANDARD 12PIN PER DECK ARRANGEMENT NOTE: 1. ONE DECK EQUALS TWO WAFERS. 2. ADD .300 FOR EACH ADDITIONAL DECK. 1/4 DIAMETER SHAFTS ARE AVAILABLE. 3. 12 FIXED POSITION USES ADJUSTABLE STOP DIMENSIONS. CONTACT FACTORY. CUSTOM SWITCHES ARE AVAILABLE. CONTACT THE FACTORY WITH YOUR COMPLETE SPECIFICATIONS. 2010 Yonkers Road Raleigh, NC 27604 ELECTRONIC PRODUCTS UNIT OF ELECTRO SWITCH CORP. Telephone: (888) ROTARYS or (919) 833-0707 Fax: (800) 909-9171 or (919) 833-8016 9