290WS011-24 Glenair

Geo-Marine Accessories 290-011 and 290-012 Stainless Steel Molding Adapters STAINLESS STEEL MOLDING ADAPTERS, STANDARD OR WITH OPTIONAL CABLE ENTRY DIAMETERS Tips To select the appropriate molding How To Order adapter, consider the following basic suggestions to ensure a high integrity, Sample Part Number 290WS011 18 quality molded termination: Basic Number 290WS011 Select a molding adapter which Shell Size See Table I will provide adequate inside working room to accept the termination envelope, especially if there are shield terminations, splices, etc. If the termination is to be molded with neoprene or other material using a transfer molding process, select the molding adapter cable entry diameter close to the How To Order outside diameter of the cable or Sample Part Number 290WS012 18 12 termination envelope. Basic Number 290WS012 Shell Size See Table II Cable Entry Size See Table II Notes 1. Prior to use, lubricate O-rings with high grade silicone lubricant (Moly- kote M55 or equivalent). 2. Material: Adapter - stainless steel. O-ring - nitrile 290WS011 STANDARD 290WS012 OPTIONAL CABLE ENTRY DIAMETERS 2.00 Tightening & Staking (50.8) 1.28 (32.5) O-ring Indentations Max Max A Thread A Thread .60 .60 O-ring (15.2) (15.2) D B C E G F D Tightening & Staking Indentations 2014 Glenair, Inc. Series 22 Geo-Marine U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com C-2 E-Mail: sales glenair.com290-011 and 290-012 Stainless Steel Molding Adapters Table I: 290WS011 Fixed Entry Dimensions Shell Size A Thread Class 2B B Dia Max C Dia D Dia 10 5/8 - 24 UNEF .855 (21.7) .430 (10.9) .670 (17.0) 12 3/4 - 20 UNEF .965 (24.5) .535 (13.6) .780 (19.8) 14 7/8 - 20 UNEF 1.090 (27.7) .660 (16.8) .905 (23.0) 16 1 - 20 UNEF 1.220 (31.0) .785 (19.9) 1.020 (25.9) 18 1 1/8 - 16 UN 1.370 (34.8) .880 (22.4) 1.135 (28.8) 20 1 1/4 - 16 UN 1.525 (38.7) 1.005 (25.5) 1.250 (31.8) 22 1 3/8 - 16 UN 1.655 (42.0) 1.130 (28.7) 1.383 (35.1) 24 1 1/2 - 16 UN 1.775 (45.1) 1.255 (31.9) 1.510 (38.4) Table II: 290WS012 Variable Entry Dimensions Shell Size A Thread Class 2B E Dia Max Max Entry F Dia G Dia 10 5/8 - 24 UNEF .855 (21.7) .430 (10.9) .670 (17.0) 12 3/4 - 20 UNEF .965 (24.5) 12 .535 (13.6) .780 (19.8) 14 7/8 - 20 UNEF 1.090 (27.7) .660 (16.8) .905 (23.0) 16 1 - 20 UNEF 1.220 (31.0) 16 .785 (19.9) 1.020 (25.9) 18 1 1/8 - 16 UN 1.370 (34.8) .880 (22.4) 1.135 (28.8) 20 1 1/4 - 16 UN 1.525 (38.7) 20 1.005 (25.5) 1.250 (31.8) 22 1 3/8 - 16 UN 1.655 (42.0) 1.130 (28.7) 1.383 (35.1) 24 1 1/2 - 16 UN 1.775 (45.1) 24 1.255 (31.9) 1.510 (38.4) Table IV: Table V: Replacement O-Ring Torque Values Part Numbers * Torque Shell Piston Entry No. 5 In. Lbs. Size O-Ring 10 80 10 2-014 12 100 12 2-016 14 120 14 2-018 16 120 16 2-020 18 140 C 18 2-022 20 140 20 2-024 22 140 22 2-026 24 150 24 2-028 * Parker o-ring part numbers. Compound N674-70 or equivalent. Instructions for using cable molding adapters 1. Slide 290WS011/012 adapter over cable Please note that the tightening/staking indentations are on the 2. Prepare cable and wires 290WS011/012Adapter, NOT on the Marine Bronze Coupling Nut. The 3. If using shrink sleeves, slide them over wire insulation and holes in the coupling nut retain the spring for the anti-decoupling solder terminated wires to solder cup contacts slide shrink feature of the cable plug. sleeves to correct position and apply recommended heat. The TG70 Strap Wrench and the 600-076 Torque Wrench should be 4. Slide 290WS011/012 adapter and attach hand-tight to plug utilized to properly torque the cable/plug assembly to the appropriate connector. receptacle 5. Use Plug Holding Tool (P/N 600-005) along with Hand Held Torque Wrench (P/N 600-076) and Spanner Wrench (P/N 600- 171) to tighten to recommended torque value. 2014 Glenair, Inc. Series 22 Geo-Marine U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com C-3 E-Mail: sales glenair.com Geo-Marine Accessories