Joysticks Joysticks SERIES 68B Hall Effect Rocker Switch FEATURES Ratiometric analog output Sealed to IP67 dynamic - even during actuation Rugged industrial design suited for outdoor use Provides positive tactile feedback in any environment Long operational life Redundant output for safety Available with 26detent and 36 latching, friction hold, or spring return (no detent) Choices of cable length Choices of accent color APPLICATIONS Dash-panel and armrest controls Hydraulic uid ow control Engine speed control Heavy duty industrial equipment Remote control belly boxes DIMENSIONS in inches, mm TOP VIEW THIS VIEW APPLIES TO 68B-XXX-0 PART NUMBERS ONLY MOUNTING PANEL OPTIONS Mounting Panel Recommendations 1. Fasteners should be 4 thread forming screws for plastic. 2. Mounting torque to be 3-5 in-lbs, 8 in-lbs maximum. 3. Diameter of mounting holes in customer panel to be 0.110 2.8mm . Diameter of mounting holes in switch are 0.100 2.54mm . 4. Length of mounting screws to be: (panel thickness) + 0.140 3.56mm or less 5. Minimum spacing between two units is 1.080 27.43mm from centerline to centerline PANEL CUTOUT GUIDELINES Grayhill, Inc. 561 Hillgrove Avenue LaGrange, Illinois 60525-5997 USA Phone: 708-354-1040 Fax: 708-354-2820 www.grayhill.comJoysticks Joysticks BLOCK DIAGRAM & JOYSTICK OUTPUT WAVEFORM PINOUT AND WIRE COLOR CHART SPECIFICATIONS Electrical Specifications Operating Voltage on Pin 1 (VDD): 5.0V Pull-Out Force: 45 lbs. minimum Humidity, 85/85: Meets MIL-STD 202, 0.5V Paddle Impact: 0.5 lbs. weight dropped 3x Method 103B, 500 hours Absolute Maximum Voltage* on Pin 1 Solar Radiation: Meets ISO 4892-2, Method from height of 0.3m (VDD): -18 V min, +18 V max (t < 1 h) Paddle Side-Load: 45 lbs. minimum A, Cycle 1, 1000 hours Operating Current: 15 mA typ., 20 mA, max. Mounting Torque: 3-5 in-lbs recommended, Chemical Resistance: Meets IEC 60068- Output Voltage is Analog (Ratiometric to 2-74 8 in-lbs maximum Operating Voltage) Salt Fog: Meets MIL STD 810G Latching Actuation Force: 1300g PEAK Output at Center Position: 50% VDD Dielectric: Meets MIL-STD-202G, Method 300g Output at Full Travel: 10% VDD or 90% 301 Detent Actuation Force: 800g PEAK 200g VDD depending on configuration Insulation Resistance: Meets MIL-STD- Return to Center Life: 2 million cycles Output Voltage Tolerance: 202G, Method 302 minimum** 3% VDD at full travel Detent Life: 200,000 cycles minimum 5% VDD at center position Materials and Finishes Latching Life: 200,000 cycles minimum Output Current: 1 mA, max. Paddle: Thermoplastic with elastomer finger Friction Hold Life: 200,000 cycles minimum Recommended Load: 10 K Ohm pull-down grip ** One cycle is defined as full travel from the center to the +40 resistor. Cable Assembly: 22AWG stranded, tin- direction, then full travel to the -40 direction, then return to the Sensor Error: When a sensor error occurs, coated copper wires in PVC insulation center the output goes to < 4% of operating voltage Connector Body: Thermoplastic (VDD ) Terminals: Nickel Environmental Ratings Seal: IP67 as mounted RoHS Compliant *Exceeding the Absolute Maximum Voltage may result in permanent damage to the device. This is a stress rating Altitude: Meets MIL-STD-810G, Method 500.4, only and functional operation of the device at those or any Procedure I other conditions above those indicated in the operation EMC Ratings Thermal Shock: Meets MIL-STD-810G, listings of this specification is not implied. Radiated Immunity: Meets ANSI/ASAE EP455 Method 503.4, Procedure I 5.16 (100 V/M, 0. 014-1000 MHz, 3 orientations) Physical & Mechanical Ratings Operating High Temperature: +85C, Meets Radiated Emissions: Meets ISO 14982, Sec Vibration: Random, meets MIL-STD-810G, IEC 68-2-2, Test Aa 6.4 (Broadband), Sec 6.5 (Narrowband) limits Method 514.6, Procedure I Operating Low Temperature: -40C, Meets Conducted Emissions: Meets CISPR 25, Mechanical Shock: Meets MIL-STD 202, IEC 68-2-1, Test Aa Class 5 Method 213B Test Condition A Storage High Temperature: +100C, Meets Electrostatic Discharge: Meets ANSI/ASAE Transit Drop: Meets MIL-STD-810G, IEC 68-2-2, Method Aa EP455 5.12, Level 1 Method 516.6, Procedure II Storage Low Temperature: -55C, Meets Power Frequency Magnetic Field: Meets IEC Terminal Strength: 10 lbs. minimum, tested IEC 68-2-1, Method Aa 61000-4-8, 30 A/m per MIL-STD-202, Method 211A Damp Heat Cycle: Meets IEC/EN 60068-2-38 Push-Out Force: 45 lbs. minimum Z/AD ORDERING INFORMATION PADDLE FUNCTION 0 = No detent or latching ACCENT COLOR 1 = 26 detent + 36 latching 1 = Black 2 = Friction hold 2 = Blue (Custom options available, contact Grayhill) 3 = Purple 4 = Yellow 68B-XXX-X 5 = Green 6 = Red TERMINATION 0 = No Connector 8 wires with stripped ends SUPPLY VOLTAGE* 4 = 4.00 Cable with Deutsch Connector 5 = 5.0V 6 = 6.00 Cable with Deutsch Connector *Output is proportional to VD D 8 = 8.00 Cable with Deutsch Connector For prices and custom configurations, contact a local sales office, an authorized distributor , or Grayhill s sales department. Grayhill, Inc. 561 Hillgrove Avenue LaGrange, Illinois 60525-5997 USA Phone: 708-354-1040 Fax: 708-354-2820 www.grayhill.com