DF50-20DP-1V(62)

1mm Pitch, Board to Cable Lock Connector DF50 Series It provides clear tactile click and secure mating Timing of locking function Simultaneous timing of locking function and Figure 1. contact mating provides a clearer tactile click. Robust structure resistant to wrenching forces Features 1. It provides clear tactile click and secure mating Locking function and contact mating occur simultaneously, for a clearer tactile click. (Please refer to Figure 1 on the right) 2. Robust structure resistant to wrenching forces Thick and robust housing wall provides higher strength against cracking. Insertion depth for mating housings protects against wrenching. (Please refer to Figure 2 on the right) 3. Robust and reliable lance structure Insertion depth for mating protects against wrenching. High lance strength by mating with crimp contact on the Thick and robust outer wall provides higher surface Figure 2. strength and prevents cracking. (Please refer to Figure 3 on the right) 4. Ensured adsorption area eliminates the need Robust and reliable lance structure for adsorption gap. Adequate adsorption area is ensured despite the small size, The lance mates with the crimp allowing for automatic mounting without adsorption gap. contact on the surface. (*Specifications for adsorption gap may be provided according to your requirements) 5. Insulation outer diameter 0.9mm, compatible with AWG#28 Despite 1 mm Pitch, it is compatible with 0.9mm, UL1061 AWG#28 Cable (0.1277) It is possible to visually inspect the assembled lance. Figure 3. 2013.4 1DF50 Series1mm Pitch, Board to Cable Lock Connector Product Specifications Operating Temperature Range -35 to + 85C (Note 1) Current Rating 1A Operating Humidity Range 20 to 80% Ratings Storage Temperature Range -10 to + 60C (Note 2) Voltage Rating AC/DC 100V Storage Humidity Range 40 to 70% (Note 2) Items Specifications Conditions 1. Insulation resistance No less than 500M Measured at DC 100V 2. Withstand voltage No flashover or breakdown AC300V is applied for one minute 3. Contact resistance No more than 30m Measured at 1mA and no higher than 20mV 10 cycles in each of three directions at frequency 10-55 Hz, 4.Vibration Resistance No electric outage of 1s or greater half amplitude 0.75 mm 2 Accelerated velocity: 490m/s for 11ms, half-sine in 3 directions, 5. Shock Resistance No electric outage of 1s or greater 3 times for each direction Contact resistance: no more than 50m; Temperature: 402C; humidity: 90 to 95%, left as it is for 96 6.Moisture-resistance insulation resistance: no less than 100M hours Contact resistance: no more than 50m; (-55C for 30 minutes 5 to 35C for 2 to 3 minutes 85C for 7. Temperature cycles insulation resistance: no less than 500M 30 minutes 5 to 35C for 2 to 3 minutes) in 5 cycles 8. Push-pull durability Contact resistance: no more than 50m 30 times of push-pull operation life 9. Solder Heat There should be no dissolution of the resin part which Reflow: according to the Recommended Temperature Profile Resistance will influence the performance. Hand soldering: temperature of soldering iron at 350C for 3 to 4 seconds (Note 1) Temperature rise at the time of electrification is included. (Note 2) The term storage refers to the long-term storage condition of unused products before PCB mounting. Operating Temperature Range is applied to the deenergized state after mounting of PCB and the temporary storage state during transportation. (Note 3) The above specifications are representative of this series. Please refer to delivery specifications for official individual agreement. Materials Product Part Materials Color / Treatment UL Regulation Insulator LCP Black UL94V-0 Contact Brass Gold plating --------- Header (on the board side) Metal fitting Brass (Note 1) Tin Plating --------- Locking metal fittings (DF50) Stainless steel --------- --------- Black (DF50A) Crimp socket Insulator PBT UL94V-0 White (DF50S) Crimp contact Contact Phosphorous Bronze Gold plating --------- (Note 1) Phosphor bronze is applied a material for only to the single-row straight pin header. Product Number Structure Connector Crimp contact DF50 * DP 1 V ** DF50 2830 SCF A Wire connection method/Geometry of terminal Series Name: DF50 (Double-row pin header) C: Crimp socket DF50S (Double-row crimp socket) V: SMT Straight Type DF50A (Single-row) H: SMT Right Angle Type Number of contacts: 20, 30, 40, 50 (Double-row) Specifications : 2 to 16 (Single-row) 51: SMT Embossed packaging Connector type 52: SMT Embossed packaging (with cap, DF50) DP: Double-row pin header Applicable wire size DS: Double-row socket 2830: AWG28, 30 P: Single-row pin header 3032: AWG30, 32 (Under development) S: Single-row socket Method type/Packaging type Contact Pitch: 1mm SCF: Socket contact reel Plating specifications A: Gold plating 2