17mm 0.5mm Pitch, 0.9mm Height, FPC/FFC Connectors FH19C Series/FH19SC Series FH19C FPC/FFC thickness : 0.20.03mm Actuator color: Brown FH19SC FPC/FFC thickness : 0.30.03mm Actuator color: Black 0.9mm high (30 pos. shown) Features 1. Low-profile 0.5mm pitch FPC/FFC Connectors Miniaturization of portable equipment and personal mobile devices has created increased demand for a low 0.9mm profile, high density, and high reliability connectors. *The design of this connector has been made thinner and smaller, with a height of 0.9mm and width of 3mm. *PCB footprint: Reduced approximately 48% (as compared with Hirose Electric s 0.5mm pitch FH12 Series connectors) Can be mounted over conductive traces *Connector weight: Reduced approximately 78% (as compared with Hirose Electric s 0.5mm pitch FH12 Series connectors) 2. Conductive traces on the PCB can run under the connector All bottom surface of the connector is solid, without any exposure of the contact. 3. Proven Flip-Lock Actuator System assures Enclosed construction easy and reliable operation (No exposed contacts) Rotating actuator permits easy insertion and reliable Metal fittings connection with the FPC & FFC. (Leadless) Tactile sensation confirms complete mechanical locking of the actuator and the electrical connection. Metal Fittings (Leadless Type) 4. Accepts 0.2mm & 0.3mm thick FPC/FFC No protrusions on No exposed contacts on the bottom of the connector. the sides allows The connector will also terminate with 0.2mm thick Flat close side-by-side Flexible Cable (FFC). board placement. 5. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging Actuator Temporary Hold Mechanism contains 5000 connectors. 6. Wide range of contact counts The contact positions available range from 4 to 50. 7. Satisfies Halogen-free requirements All materials and substances used in this product comply with the Halogen-free standards. * Defined according to IEC61249-2-21 Br : 900ppm max, Cl : 900ppm max, Br+Cl : 1,500ppm max Actuator stays open during insertion of the FPC/FFC. 1 2019.4e 3mmFH19C & FH19SC Series0.5mm Pitch, 0.9mm Height, FPC/FFC Connectors Product Specifications Operating temperature range Storage temperature range ( ) Note 1 Current rating 0.5A + + -55 to 85 (Note 2) -10 to 50 (Note 3) Rating Operating humidity range Storage humidity range Voltage rating 50V AC Relative humidity 90% max. (No condensation) Relative humidity 90% max. (No condensation) Thickness : = 0.2 0.03mm Gold plated Recommended FH19C Series FPC, FFC FH19SC Series Thickness : = 0.3 0.03mm Gold plated Item Specification Conditions 1. Insulation resistance 500M min. 100V DC 2. Withstanding voltage No flashover or insulation breakdown 150V AC/1 minute 100m max. 3. Contact resistance 1mA *Including FPC/FFC conductor resistance 4. Durability Contact resistance : 100m max. 20 cycles (insertion/ withdrawal) No damage, cracks, or parts dislocation. No electrical discontinuity of 1s or more. Frequency : 10 to 55Hz, single amplitude of 0.75mm, 5. Vibration Contact resistance : 100m max. 10 cycles in each of the 3 directions No damage, cracks, or parts dislocation. No electrical discontinuity of 1s. min. 2 Acceleration of 981m/s , 6ms duration, sine half- 6. Shock Contact resistance : 100m max. wave waveform, 3 cycles in each of the 3 axis. No damage, cracks, or parts dislocation. Contact resistance : 100m max. 96 hours at temperature of 40 and humidity of 7. Humidity Insulation resistance : 100M min. 90 to 95% (Steady state) No damage, cracks, or parts dislocation. + + + + + Temperature : -55 15 to 35 85 15 to 35 Contact resistance : 100m max. / / / + Time : -30 2 to 3 30 2 to 3(Minutes) 8. Temperature cycle Insulation resistance : 100M min. / / / No damage, cracks, or parts dislocation. 5 cycles 9. Resistance to Reflow : At the recommended temperature profile No deformation of components affecting performance. soldering heat Manual soldering : 3505 for 5 seconds Note 1 : When passing the current through all of the contacts, use 70% of the current rating. Note 2 : Includes temperature rise caused by current flow. Note 3 : The term storage refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.Information Materials / Finish Part Material Finish Remarks Color: Beige Color: Brown (FH19C Series) Insulator LCP UL94V-0 Color: Black (FH19SC Series) Contacts Phosphor bronze Gold plated ------- Metal fittings Phosphor bronze Pure tin reflow plated ------- Product Number Structure Refer to the chart below when determining the product specifications from the product number. Please select from the product numbers listed in this catalog when placing orders. FH 19 C - 30S - 0.5 SH (10) 1 2 3 4 5 6 7 1 Series name : FH 5 Contact pitch : 0.5mm 2 Series No. : 19 6 Terminal type SH : SMT horizontal mounting type C : FPC thickness : 0.2mm 3 SC : FPC/FFC thickness : 0.3mm Material and plating specifications : 7 FH19C : (10)...Gold plating with nickel barrier 5,000pieces/reel 4 No. of contacts : 4 to 50 (99)...Gold plating with nickel barrier 500pieces/reel FH19SC : (09)...Gold plating with nickel barrier 5,000pieces/reel (99)...Gold plating with nickel barrier 500pieces/reel 2