TCVCXO Specification Part No. + Packaging: LFTVXO076349Reel Customer Part: Description Outline (mm) The IQXT-316-9 uses ASIC technology and is designed to meet the short and medium term stability requirements of packet network synchronisation for Small Cells. Model IQXT-316-9 Model Issue number 1 Frequency Parameters Frequency 30.720MHz Frequency Tolerance 1.00ppm Tolerance Condition 25C 1C & VC=1.5V Frequency Stability 0.25ppm Operating Temperature Range -5.00 to 85.00C Inservice Short-term Frequency Stability (over any 24-hr timeslot fixed supply voltage and load): 50 to 70C: 80ppb max 15 to 85C: 100ppb max -5 to 85C: 250ppb max Ageing: 20ppb max/day 200ppb max/month 1ppm max/year 2ppm max over 3yrs Temperature Rate of Change (maximum rate of change of temperature condition for guaranteed stability specifications): 1C/min max Acceleration Sensitivity (gamma vector of all 3 axes from 30 to 1500Hz): Typically 2ppb/G max Supply Voltage Variation (2% change 25C, measurement referenced to frequency observed nominal Vs): 10ppb typ Load Variation (2% change 25C, measurement referenced to frequency observed nominal load): 10ppb typ Reflow Variation (pre to post reflow F, measured after 1hr recovery 25C): 1ppm max Note: The characteristics of the oscillator may be temporarily affected by the processes of assembly and soldering. The in-service short term frequency stability specification applies after 48hrs continuous operation and after the first excursion over the temperature range. Nominal conditions apply unless otherwise stated. Electrical Parameters 3.3V 5% Supply Voltage Current Draw 4.500mA Absolute Maximum Ratings: Supply Voltage (Vs): -0.5V to 7V Control Voltage (VC): -0.5V to 9V All other inputs: -0.5V to Vs+0.5V Power Dissipation: 100mW max Junction Temperature: 150C max Note: Operating beyond these limits may result in change or permanent damage to the oscillator. Sales Office Contact Details: UK: +44 (0)1460 270200 France: 0800 901 383 Email: info iqdfrequencyproducts.com Germany: 0800 1808 443 USA: +1.760.318.2824 Web: www.iqdfrequencyproducts.com Printed on 5 Aug 21 0:06 using Part Data Sheet V1.0018 Page 1 of 3TCVCXO Specification Part No. + Packaging: LFTVXO076349Reel Customer Part: Frequency Adjustment Pulling 7ppm min to 12ppm max Control Voltage 1.5V 1.0V Input Impedance 100k min Linearity (deviation from straight line curve fit): 1% max Frequency Tuning Slope: Positive Modulation Bandwidth: 1Hz min Note: Pulling referenced to frequency VC=1.5V Output Details Output Compatibility Clipped Sine Drive Capability 10k//10pF Output Voltage Level: 0.8V pk-pk min, 1.1V pk-pk typ Start Up Time (amplitude within 90% of specified output level): 15ms max Output: DC coupled Temperature Sensor Output (pad 3): Vtemp ( 25C): 1.76V typ Slope Option: -2.1mV/C typ Resistive Load: 100k min Capacitive Load: 30pF max Output Impedance ( 25C): 1k typ Sensor Linearity: 1.5% typ Output Control Tri-State Mode: Logic 0 (20%Vs max) to pad 6 disables the oscillator output, the output goes to a high impedance state. Logic 1 (60%Vs min) or no connection to pad 6 enables the oscillator output. Note: The tri-state control (enable) input pad has an internal 100k pull up resistor which allows it to be left unconnected if not used. When in tri-state mode, the output stage is disabled, but the oscillator and compensation circuit are still active (Current Consumption: 2mA typ). Output Enable Time: 100s max Noise Parameters Phase Noise 25C (typ): -65dBc/Hz 1Hz -92dBc/Hz 10Hz -125dBc/Hz 100Hz -143dBc/Hz 1kHz -149dBc/Hz 10kHz -152dBc/Hz 100kHz -155dBc/Hz 1MHz Phase Jitter (12kHz to 5MHz): 300fs RMS typ Sales Office Contact Details: UK: +44 (0)1460 270200 France: 0800 901 383 Email: info iqdfrequencyproducts.com Germany: 0800 1808 443 USA: +1.760.318.2824 Web: www.iqdfrequencyproducts.com Printed on 5 Aug 21 0:06 using Part Data Sheet V1.0018 Page 2 of 3