IS42S16400J IS45S16400J 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) JULY 2014 SYNCHRONOUS DYNAMIC RAM FEATURES OVERVIEW ISSI s 64Mb Synchronous DRAM is organized as 1,048,576 Clock frequency: 200, 166, 143, 133 MHz bits x 16-bit x 4-bank for improved perfor mance. The Fully synchronous all signals referenced to a synchronous DRAMs achieve high-speed data transfer positive clock edge using pipeline architecture. All inputs and outputs signals Inter nal bank for hiding row access/precharge refer to the rising edge of the clock input. Single 3.3V power supply LVTTL interface Programmable burst length KEY TIMING PARAMETERS (1, 2, 4, 8, full page) Programmable burst sequence: Parameter -5 -6 -7 Unit Sequential/Interleave Clk Cycle Time CAS Latency = 3 5 6 7 ns Self refresh modes CAS Latency = 2 7.5 7.5 7.5 ns Auto refresh (CBR) Clk Frequency 4096 refresh cycles ever y 64 ms (Com, Ind, A1 CAS Latency = 3 200 166 143 Mhz grade) or 16ms (A2 grade) CAS Latency = 2 133 133 133 Mhz Random column address ever y clock cycle Access Time from Clock Programmable CAS latency (2, 3 clocks) CAS Latency = 3 4.8 5.4 5.4 ns CAS Latency = 2 5.4 5.4 5.4 ns Burst read/wr ite and burst read/single wr ite operations capability Burst ter mination by burst stop and precharge command ADDRESS TABLE OPTIONS Parameter 4M x 16 Package: Configuration 1M x 16 x 4 54-pin TSOP II banks 54-ball TF-BGA (8mm x 8mm) Refresh Count 60-ball TF-BGA (10.1mm x 6.4mm) Com./Ind. 4K/64ms A1 4K/64ms Operating Temperature Range A2 4K/16ms o o Commercial (0 C to +70 C) o o Row Addresses A0-A11 Industrial (-40 C to +85 C) o o Column Addresses A0-A7 Automotive Grade A1 (-40 C to +85 C) o o Automotive Grade A2 (-40 C to +105 C) Bank Address Pins BA0, BA1 Auto Precharge Pins A10/AP Copyright 2014 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be ex- pected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized b.) the user assume all such risks and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. www.issi.com 1 Rev. G 7/30/2014IS42S16400J IS45S16400J GENERAL DESCRIPTION The 64Mb SDRAM is a high speed CMOS, dynamic other three banks will hide the precharge cycles and provide random-access memor y designed to operate in 3.3V seamless, high-speed, random-access operation. memory systems containing 67,108,864 bits. Internally SDRAM read and write accesses are burst oriented starting configured as a quad-bank DRAM with a synchronous at a selected location and continuing for a programmed interface. Each 16,777,216-bit bank is organized as 4,096 number of locations in a programmed sequence. The rows by 256 columns by 16 bits. registration of an ACTIVE command begins accesses, The 64Mb SDRAM includes an AUTO REFRESH MODE, followed by a READ or WRITE command. The ACTIVE and a power-saving, power-down mode. All signals are command in conjunction with address bits registered are registered on the positive edge of the clock signal, CLK. used to select the bank and row to be accessed (BA0, All inputs and outputs are LVTTL compatible. BA1 select the bank A0-A11 select the row). The READ or WRITE commands in conjunction with address bits The 64Mb SDRAM has the ability to synchronously burst registered are used to select the starting column location data at a high data rate with automatic column-address for the burst access. generation, the ability to interleave between internal banks to hide precharge time and the capability to randomly Programmable READ or WRITE burst lengths consist of change column addresses on each clock cycle during 1, 2, 4 and 8 locations, or full page, with a burst terminate burst access. option. A self-timed row precharge initiated at the end of the burst sequence is available with the AUTO PRECHARGE function enabled. Precharge one bank while accessing one of the FUNCTIONAL BLOCK DIAGRAM CLK DQM CKE COMMAND DATA IN CS DECODER BUFFER RAS 16 16 & CAS CLOCK WE REFRESH MODE DQ 0-15 A10 GENERATOR CONTROLLER REGISTER 12 VDD/VDDQ SELF DATA OUT REFRESH A11 BUFFER GND/GNDQ CONTROLLER 16 16 A9 A8 A7 REFRESH A6 COUNTER A5 A4 4096 A3 4096 MEMORY CELL A2 4096 ARRAY A1 4096 12 A0 BANK 0 ROW ROW BA0 ADDRESS ADDRESS BA1 LATCH BUFFER 12 12 SENSE AMP I/O GATE 256K (x 16) COLUMN BANK CONTROL LOGIC ADDRESS LATCH 8 BURST COUNTER COLUMN DECODER COLUMN ADDRESS BUFFER 8 2 Integrated Silicon Solution, Inc. www.issi.com Rev. G 7/30/2014 MULTIPLEXER ROW DECODER