Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Open Mode Design (FO-CAP), X7R Dielectric, 16 200 VDC (Commercial & Automotive Grade) Overview KEMETs Ceramic Open Mode capacitor in X7R dielectric circuit failures. Although flexible termination technology is designed to significantly minimize the probability of a does not eliminate the potential for mechanical damage that low IR or short circuit condition when forced to failure in may propagate during extreme environmental and handling a board stress flex situation, thus reducing the potential conditions, it does provide superior flex performance over for catastrophic failure. The Open Mode capacitor may standard termination systems. When combined with flexible experience a drop in capacitance however, a short is termination technology these devices offer the ultimate level unlikely because a crack will not typically propagate of protection against a low IR or short circuit condition. Open across counter electrodes within the devices active area. Mode devices compliment KEMET s Floating Electrode Since there will not be any current leakage associated (FE-CAP) and Floating Electrode with Flexible Termination with a typical Open Mode flex crack, there is no localized (FF-CAP) product lines by providing a fail-safe design heating and therefore little chance for a catastrophic and optimized for mid to high range capacitance values. These potentially costly failure event. devices exhibit a predictable change in capacitance with respect to time and voltage and boast a minimal change Driven by the demand for a more robust and reliable in capacitance with reference to ambient temperature. component, the Open Mode capacitor was designed for Capacitance change is limited to 15% from 55C to +125C. critical applications where higher operating temperatures and mechanical stress are a concern. These capacitors are widely used in automotive circuits as well as power supplies (input and output filters) and general electronic applications. Concerned with flex cracks resulting from excessive tensile and shear stresses produced during board flexure and thermal cycling These devices are available with KEMET s Flexible termination technology which inhibits the transfer of board stress to the rigid ceramic body, therefore mitigating flex cracks which can result in low IR or short Ordering Information C 1210 J 685 K 3 R A C TU Rated Failure Case Size Specification/ Capacitance Capacitance Packaging/Grade 1 Ceramic Voltage Dielectric Rate/ Termination Finish ( x ) Series Code (pF) Tolerance (C-Spec) (VDC) Design 0805 F = Open Mode Two significant K = 10% 4 = 16 R = X7R A = N/A C = 100% Matte Sn SeePackaging 1206 J = Open Mode digits and M = 20% 3 = 25 L = SnPb C-Spec 1210 withFlexible number of zeros 5 = 50 (5% Pb minimum) Ordering 1812 Termination 1 = 100 Options Tabl 2 = 200 1 Additional termination finish options may be available. Contact KEMET for details. 1 SnPb termination finish option is not available on automotive grade product. Built Into Tomorrow KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1012 X7R OPENMODE SMD 10/28/2020 1 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.comSurface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) Open Mode Design (FO-CAP), X7R Dielectric, 16 200 VDC (Commercial & Automotive Grade) Packaging C-Spec Ordering Options Table Packaging/Grade Packaging Type Ordering Code (C-Spec) 1 Commercial Grade Bulk Bag Not Required (Blank) 7 Reel/Unmarked TU 7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked 7210 (EIA 0805 and larger case sizes) 7 Reel/Marked TM 7040 (EIA 0603) 13 Reel/Marked 7215 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 7081 2 13 Reel/Unmarked/2 mm pitch 7082 3 Automotive Grade 7 Reel AUTO AUTO7411 (EIA 0603 and smaller case sizes) 13 Reel/Unmarked AUTO7210 (EIA 0805 and larger case sizes) 2 7 Reel/Unmarked/2 mm pitch 3190 2 13 Reel/Unmarked/2 mm pitch 3191 1 Default packaging isBulk Ba. An ordering code C-Spec is not required forBulk Ba packaging. 1 The termsMarke andUnmarke pertain to laser marking option of capacitors. All packaging options labeled asUnmarke will contain capacitors that have not been laser marked. 2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case size devices. For more information regarding 2 mm pitch option seeTape & Reel Packaging Informatio. 3 Reeling tape options (Paper or Plastic) are dependent on capacitor case size ( x ) and thickness dimension. SeeChip Thickness/Tape & Reel Packaging Quantitie andTape & Reel Packaging Informatio. 3 For additional Information regardingAUT C-Spec options, seeAutomotive C-Spec Informatio. 3 All Automotive packaging C-Specs listed exclude the option to laser mark components. Please contact KEMET if you require a laser marked option. For more information seeCapacitor Markin. Benefits 55C to +125C operating temperature range Non-polar device, minimizing installation concerns Open Mode/fail open design 100% pure matte tin-plated termination finish allowing for Mid to high capacitance flex mitigation excellent solderability Lead (Pb)-free, RoHS and REACH compliant Commercial and Automotive (AECQ200) grades available EIA 0805, 1206, 1210, and 1812 case sizes SnPb termination finish option available upon request DC voltage ratings of 16 V, 25 V, 50 V, 100 V, and 200 V (5% Pb minimum) Capacitance offerings ranging from 1,000 pF to 6.8 F Flexible termination option available upon request Available capacitance tolerances of 5%, 10%, and 20% Applications Typical applications include input side filtering (power plane/bus), high current (battery line) and circuits that cannot be fused to open when short circuits occur due to flex cracks. Markets include automotive applications that are directly connected to the battery and/or involve conversion to a 42 V system and raw power input side filtering in power conversion. KEMET Electronics Corporation KEMET Tower One East Broward Boulevard C1012 X7R OPENMODE SMD 10/28/2020 2 Fort Lauderdale, FL 33301 USA 954-766-2800 www.kemet.com