XPort Embedded Device Server Data Sheet General Description The Lantronix XPort embedded device server is Where theres a need for custom user interfaces the most compact, integrated solution available to and a desire to use common and familiar tools, the web-enable any device with a serial interface. By XPort module can serve web pages to a web simply adding an XPort unit to a product design, browser. The XPort unit becomes a conduit device manufacturers cut their design cycle by as between you and your device over the network or much as 80% and are able to offer Ethernet Internet. connectivity in record time. x The Lantronix DeviceInstaller utility is a Windows based configuration tool that simplifies installation and setup. The XPort module can also be set up locally through its serial port, or remotely over a network using Telnet or a web browser. Flash memory provides for maintenance-free nonvolatile storage of web pages, and allows future system The XPort module offers the highest level of software upgrades. integration available in a device server. Within a Using our highly integrated hardware and software compact RJ45 package is a DSTni EX 186 platform, you will add profit to your bottom line by controller, memory, 10/100 Ethernet transceiver, significantly reducing product development time, high-speed serial port, status/diagnostic LEDs, and risk, and cost. 3 programmable I/O pins. In the space that is normally consumed by a connector, the XPort unit provides a complete networking interface. To enable access to a local network or the Internet, Key Features the XPort module integrates a fully developed The only complete, integrated solution in an RJ45 TCP/IP network stack and OS. The XPort unit also form factor includes an embedded web server used to remotely Complete integrated solution configure, monitor, or troubleshoot the attached device. Embedded web server 10/100Mbit Ethernet Auto-Sensing Stable, field proven TCP/IP protocol suite and web- based application framework Easy configuration through a web interface Easy customization of HTML web pages and configuration screens Interactive web pages through the use of Java applets E-mail 128-, 192-, or 256-bit AES Rijndael encryption (Optional) EMI tested and compliant Extended operating temperature: -40 to +85 C normal mode -40 to +75 C high-performance mode High-performance processor (12 MIPS at 48 MHz, 22 MIPS at 88 MHz) Network overhead handled by XPort unit Password protection Upgrade XPort modules firmware over the network 3.3V power Serial-to-10/100 Ethernet conversion 921,600 baud serial speed 910-815 I XPort Embedded Device Server Data Sheet Copyright 2014, Lantronix. All rights reserved. Table 1 - PCB Interface Signals Hardware & Software Description Signal Pin Function The XPort unit is a complete solution (hardware and Name software) for web-enabling your edge devices. Packed GND 1 Circuit Ground into an RJ45 connector smaller than your thumb, this Vcc 2 +3.3V Power In powerful device server comes with a 10BASE- Reset (In) 3 External Reset In T/100BASE-TX Ethernet connection, a reliable and Data OUT 4 Serial Data Out proven operating system stored in flash memory, an Data IN 5 Serial Data In embedded web server, a full TCP/IP protocol stack, and standards-based (AES) encryption. CP1 can be configured as follows: Flow control: RTS (Request to Send) The XPort software runs on a DSTni EX controller output driven by DSTnis built-in UART which has 256 KB of SRAM, 16 KB of boot ROM, and for connection to CTS of attached a MAC with integrated 10/100BASE-TX PHY. The device. CP1 6 XPort module communicates to the edge device Programmable input/output: CP1 can through a 3.3V serial interface and three general- be driven or read through software purpose programmable I/O pins. 512 KB of flash control, independent of serial port memory is included for storing firmware and web activity. pages. The XPort runs on 3.3V, and has a built-in CP2 can be configured as follows: voltage supervisory circuit that will trigger a reset if the Modem control: DTR (Data Terminal supply voltage drops to unreliable levels (2.7V). A Ready) output driven by DSTnis built- in UART for connection to DCD of built-in 1.8V regulator drives the processing core of CP2 7 attached device. the EX controller. Programmable input/output: CP2 can An RJ45 Ethernet cable connects directly into an be driven or read through software control, independent of serial port XPort unit. Ethernet magnetics, status LEDs, and activity. shielding are built in. The XPort module was designed CP3 can be configured as follows: to meet class B emissions levels, which makes the Flow control: CTS (Clear to Send) electromechanical integration very simple. input read by DSTnis built-in UART for connection to RTS of attached device. Tx MAGNETICS LEDs Rx Modem control: DCD (Data Carrier FLASH 25MHz Detect) input read by DSTnis built-in CP3 8 UART for connection to DTR of DSTni EX RJ45 attached device. CMOS IO RESET +3.3VDC Programmable input/output: CP3 can be driven or read through software control, independent of serial port activity. Ethernet Interface The 10/100 Ethernet magnetics, network status PCB Interface LEDs, and RJ45 connector are integrated into the XPort unit. The 8-pin PCB interface consists of 3.3V CMOS Serial In/Out, 3 Flow Control/Handshake/PIO pins, Table 2 - Ethernet Interface Signals reset input, +3.3V power, and signal ground. The serial pins and CP pins are 5V tolerant. RESET and Signal Name DIR Contact Primary Function Power are 3.3V tolerant. TX+ Out 1 Transmit Data + TX- Out 2 Transmit Data RX+ In 3 Receive Data + RX- In 6 Receive Data Not Used 4 Terminated Not Used 5 Terminated Not Used 7 Terminated Not Used 8 Terminated SHIELD Chassis Ground 910-815 I XPort Embedded Device Server Data Sheet Copyright 2014, Lantronix. All rights reserved.