SGD 21-B PanelPilot Compatible E-paper Dot Matrix Display 2.1 e-paper dot matrix display. Use PanelPilo t B software to setup and customise the display. 6 voltmeter configurations included for free. Reflective e-paper technology is sunlight readable and ultra low power. Two alarms available for configuration during software set-up. Configurable digital I/O pin. IP54 rating on front panel. Wide operating voltage of 4 9V d.c. Lascar s SGD 21-B is a low cost, ultra low power, sunlight readable, single channel voltmeter with a sleek monochrome e-paper dot matrix display. The display works with free PanelPilot B configuration software (available for Windows 7, 8 and 10) providing six analogue and digital voltmeter Apps which can then be customised to suit individual applications. Elements of each configuration that can be changed in software include custom labels, scaling and alarms. A splashscreen can be added to display on power-up. Once the App is complete, upload it to the SGD 21-B display using the CABLE USB A-SIL5. Panel or enclosure installation of the display is simple, using a panel fixing clip to mount the display. *Six configurations are available to customise and upload. Colours of each display can also be inverted if required. Minimum Typical Maximum Unit Specifications Included in the Box Standard Display SGD 21-B Accuracy 0.05 0.1 % (Panel meter, fixing kit, Linearity 1 Count quick start guide) Sample rate 2 Samples / second Accessories Operating 0 (+32) +40 (+104) C (F) USB Cable CABLE USB A-SIL5 temperature range Measurement range 0 1.25 V d.c. Input leakage current 0.1 40 nA Supply voltage 4 9 V d.c. Supply current 5 mA www.lascarelectronics.com/panelpilot electronics Issue 1 01/2018 P.G. Page 1 of 4SGD 21-B PanelPilot Compatible E-paper Dot Matrix Display Pin-out USB (PL1) D- D+ 0V VBUS: USB supply SGD 21-B VBUS D-: Negative USB data bus connection RB RA D+: Positive USB data bus connection 0V: Ground LK1 0V: Ground Basic (PL2) AIN: Analogue Input Voltage 0V: Ground V+: Power Supply Connection 0V: Ground Advanced (PL3) V+: Power Supply Connection 0V: Ground AIN: Analogue Input Voltage DI/O: Digital Input or Output (See digital configurations) ALARM: Open Collector Alarm Output 3V3 OUT: 3.3V supply generated on board Maximum Ra Rb Input Scaling Resistors 6.25v Note 1 1M 250K Two resistors may be used to alter the full scale reading of the meter. 12.6v Note 1 1M 110K See table to the right. 21.4v Note1 1M 62K 30.0v Note 1 1M 43K Display 20mA 0R (LK1) 62R The black and white display is a 2.19 E-paper display with a resolution 200mA 0R (LK1) 6.2R of 250x122. Any splashscreen graphics that are uploaded to the meter 4-20mA Note 2 0R (LK1) 62R are automatically converted to this specification but for optimal results Note1: Ensure LK1 is cut if fitting Ra. should be designed in this format. Note2: In software, Set point 1 = 1.24v (20mA) and Set point 2 = 0.248v (4mA). PanelPilot B Software Lascar s PanelPilot B software is available for download free of charge from w w w.lascarelectronics.com/software. Easy to install and use, the configuration software runs under Windows 7, 8 and 10. The software is used to setup the appearance and operation of the App and then upload these settings to the display. The software allows the following parameters to be configured: Meter type Tex t la bels (in cluding unit labe ls) Input scaling / calibration (at two points) Decimal points (entered during scaling) Sp lash screen image selection (to display a user image, such as a logo, when the meter is powered up) Digital pin www.lascarelectronics.com/panelpilot electronics Issue 1 01/2018 P.G. Page 2 of 4 AIN 0V V+ V+ 0V 0V AIN PL2 DI/O ALARM 3V3 OUT 0V PL1 PL3