195206-228

Ledex Tubular Linear Solenoids 10 50 (44.48) 10% Duty Cycle 70W 10% Duty Cycle 70W 25% Duty Cycle 28W 25% Duty Cycle 28W 8 40 (35.58) 50% Duty Cycle 14W 50% Duty Cycle 14W 100% Duty Cycle 7W 100% Duty Cycle 7W 6 30 (26.69) 4 20 (17.79) 2 10 (8.90) 0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5 (2.54) (5.08) (7.62) (10.16) (12.70) (2.54) (5.08) (7.62) (10.16) (12.70) Stroke in (mm) Stroke in (mm) 6 50 (26.69) 10% Duty Cycle 70W 10% Duty Cycle 70W 5 25% Duty Cycle 28W 25% Duty Cycle 28W (22.24) 40 50% Duty Cycle 14W 50% Duty Cycle 14W 100% Duty Cycle 7W 100% Duty Cycle 7W 4 (17.79) 30 3 (13.34) 20 2 (8.90) 10 1 (4.45) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 (2.54) (5.08) (7.62) (10.16) (12.70) (15.24) (17.78) (2.54) (5.08) (7.62) (10.16) (12.70) (15.24) (17.78) Stroke in (mm) Stroke in (mm) Force lbs (N) Force lbs (N) Speed ms Speed ms Ledex Tubular Solenoids Strokes up to 2-1/2 STA Series has enhanced design features and Life rating of 25 million improved performance actuations for STA designs Push and pull models All catalog products manufactured after April 1, 2006 are RoHS Compliant Duty Cycle Performance Curves The performance curves Duty cycle is determined in this section serve as by: ON time/(ON + OFF guides to determine the time). solenoid size needed to For example: a solenoid is produce a desired force actuated for 30 seconds, at a given stroke, duty then off for 90 seconds. cycle, and power source. 30 sec ON / (30 Sec ON + All curves were developed The Ledex STA Series Pull versus Push Type 90 sec OFF) = 30/120 = 1/4 under the following of tubular solenoids or 25% duty cycle. In Pull type solenoids, the standard test conditions: is available in three plunger is pulled into the ambient temperature Ledex tubular solenoids diameters and five solenoid coil when the of 20C, 65% relative are rated for various sizes. Both push and coil is energized. In Push humidity. duty cycles ranging from pull types are available. type solenoids, the same is continuous to 10% duty. Additionally, each size true, however, the plunger and type is available with Starting Force has a shaft extension Note that maximum ON a choice of two plunger When determining which then pushes out time for a particular configurations: flat face an applications force through a hole in the application can be a factor and 60, as well as with or requirement, apply a 1.5 end of the solenoid case. which overrides the duty without an anti-rotation safety factor. For example: Please note, however, that cycle rating. For example, flat on the mounting a load requiring 4.5 lb the magnetic field cannot at 25% duty cycle, the bushing. These options of force should utilize a be reversed to cause the maximum ON time for a offer maximum force for a solenoid providing 4.5 x opposite action to occur. given Ledex solenoid is wide range of applications. 1.5 or 6.75 lb of force. 36 seconds. If, however, The new design also the solenoid is operated improves performance Pull Type Push Type at a cycle rate which and provides longer life Shaft Plunger Plunger enables the unit to return Extension than previous tubular to ambient temperature designs. They offer quiet between ON cycles, then operation and improved the maximum ON time is reliability for demanding De-energized De-energized extended somewhat. In applications. the above example, this extended ON time is 44 Magnetic latching versions seconds. Maximum ON are available for some Energized Energized time ratings are listed models, and many models on the individual model are well suited for battery specification pages. operation. Ledex Solenoids www.ledex.com 1.937.454.2345 Fax: 1.937.898.8624 LINEAR Tubular