X-On Electronics has gained recognition as a prominent supplier of ANT-2.4-CW-RCT-SS Antennas across the USA, India, Europe, Australia, and various other global locations. ANT-2.4-CW-RCT-SS Antennas are a product manufactured by Linx Technologies. We provide cost-effective solutions for Antennas, ensuring timely deliveries around the world.
We are delighted to provide the ANT-2.4-CW-RCT-SS from our Antennas category, at competitive rates not only in the United States, Australia, and India, but also across Europe and beyond. A long established and extensive electronic component distribution network has enhanced our global reach and dependability, ensuring cost savings through prompt deliveries worldwide. Client satisfaction is at the heart of our business, where every component counts and every customer matters. Our technical service team is ready to assist you. From product selection to after-sales support, we strive to deliver a seamless and satisfying experience. Are you ready to experience the best in electronic component distribution? Contact X-ON Electronics today and discover why X-On are a preferred choice for the ANT-2.4-CW-RCT-SS and other electronic components in the Antennas category and beyond.
ANT-2.4-CW-RCT-xx Data Sheet by Product Description 10.0 mm The RCT Series -wave antenna delivers (0.39 ) outstanding performance with an innovative articulating base that allows it to tilt 90 and rotate 360 for optimum orientation. The antennas internal counterpoise eliminates external ground plane dependence and maximizes performance. The RCT attaches via a standard SMA or Part 15 compliant RP-SMA connector 95.6 mm Features (3.76 ) Internal counterpoise 113.0 mm (4.44 ) Tilts and rotates Excellent performance Omni-directional pattern Very low VSWR Fully weatherized 5.1 mm Rugged and damage-resistant (0.20 ) 8.4 mm Standard SMA or Part 15 compliant RP-SMA (0.33 ) 9.0 mm connector (0.35 ) Electrical Specifications 28.0 mm (1.10 ) Center Frequency: 2.45GHz Recom. Freq. Range: 2.402.50GHz Wavelength: -wave VSWR: 1.9 typical at center Peak Gain: 2.2dBi Impedance: 50-ohms Connector: RP-SMA Oper. Temp. Range: 40C to +90C Electrical specifications and plots measured on 10.16 cm x 10.16 cm (4.00 x 4.00 ) reference ground plane Ordering Information ANT-2.4-CW-RCT-RP (with RP-SMA connector) ANT-2.4-CW-RCT-SS (with SMA connector) 1 Revised 1/13/14VSWR Graph VSWR 1.003 Reflected Power 3:1 25% 2:1 11% 1:1 0% 2350MHz 2450MHz 2550MHz What is VSWR The Voltage Standing Wave Ratio (VSWR) is a measurement of how well an antenna is matched to a source impedance, typically 50-ohms. It is calculated by measuring the voltage wave that is headed toward the load versus the voltage wave that is reflected back from the load. A perfect match will have a VSWR of 1:1. The higher the first number, the worse the match, and the more inefficient the system. Since a perfect match cannot ever be obtained, some benchmark for performance needs to be set. In the case of antenna VSWR, this is usually 2:1. At this point, 88.9% of the energy sent to the antenna by the transmitter is radiated into free space and 11.1% is either reflected back into the source or lost as heat on the structure of the antenna. In the other direction, 88.9% of the energy recovered by the antenna is transferred into the receiver. As a side note, since the :1 is always implied, many data sheets will remove it and just display the first number. How to Read a VSWR Graph VSWR is usually displayed graphically versus frequency. The lowest point on the graph is the antennas operational center frequency. In most cases, this will be different than the designed center frequency due to fabrication tolerances. The VSWR at that point denotes how close to 50-ohms the antenna gets. Linx specifies the recommended bandwidth as the range where the typical antenna VSWR is less than 2:1. Data Sheet ANT-2.4-CW-RCT-xx 2 by
