TXE-315-KH2 TXE-418-KH2 TXE-433-KH2 WIRELESS MADE SIMPLE KH2 SERIES TRANSMITTER / ENCODER DATA GUIDE DESCRIPTION The KH2 Series is ideally suited for volume use 1.220 in OEM applications such as remote control and command, and keyless entry. Housed in a compact SMD package, it combines a highly- RF TRANSMITTER/ENCODER optimized RF transmitter with an on-board 0.630 TXE-418-KH2 encoder. When paired with a matching KH2 LOT 10000 Series receiver / decoder module, a reliable wireless link is formed, capable of transferring the status of 8 parallel inputs over distances of up to 3,000 feet. Ten tri-state address lines 10 provide 59,049 (3 ) addresses for security and 0.180 uniqueness. No external RF components are required except an antenna, making integration Figure 1: Package Dimensions straightforward. FEATURES n Low cost n Ultra-low power consumption n On-board encoder n Compact SMD package n 8 parallel binary inputs n Stable SAW-based architecture 10 n Adjustable output power n 3 addresses for security and uniqueness n Transmit enable line n No external RF components n No production tuning required APPLICATIONS INCLUDE ORDERING INFORMATION n Remote Control / Command n Keyless Entry PART DESCRIPTION TXE-315-KH2 Transmitter 315MHz n Garage / Gate Openers TXE-418-KH2 Transmitter 418MHz n Lighting Control TXE-433-KH2 Transmitter 433MHz n Call Systems RXD-315-KH2 Receiver 315MHz n Home / Industrial Automation RXD-418-KH2 Receiver 418MHz n Fire / Security Alarms RXD-433-KH2 Receiver 433MHz n Remote Status Monitoring EVAL-***-KH2 Basic Evaluation Kit n Wire Elimination *** = 315, 418 (Standard), 433.92MHz. Transmitters are supplied in tubes of 20 pcs. Revised 9/27/11ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Parameter Designation Min. Typical Max. Units Notes Supply Voltage V -0.3 to +6.0 VDC CC POWER SUPPLY Any Input or Output Pin -0.3 to V VDC CC Operating Voltage V 2.7 5.2 VDC CC Operating Temperature -30 to +70 C Supply Current I 1.5 mA 1,4 CC Storage Temperature -45 to +85 C Power-Down Current I 1.0 A PDN Soldering Temperature +225C for 10 seconds TRANSMITTER SECTION *NOTE* Exceeding any of the limits of this section may lead to permanent Transmit Frequency Range: F C damage to the device. Furthermore, extended operation at these maximum ratings may reduce the life of this device. TXE-315-KH2 315 MHz TXE-418-KH2 418 MHz TXE-433-KH2 433.92 MHz PERFORMANCE DATA Center Frequency Accuracy -75 +75 kHz These performance parameters Output Power P -4 +2 +4 dBm 2,3 VCC O are based on module operation at Harmonic Emissions P -36 dBc 2 H 1 24 LADJ/GND ANT 25C from a 3.0VDC supply unless ANTENNA PORT 2 23 D0 GND D1 3VDC 3 A9 22 otherwise noted. Figure 2 RF Output Impedance R 50 4 4 OUT GND A8 21 5 illustrates the connections VCC A7 20 ENCODER SECTION 6 TE A6 19 necessary for testing and Data Length 26 bits 3x 7 D2 A5 18 8 D3 A4 17 operation. It is recommended all Average Data Duty Cycle 50% 4 9 D4 A3 16 10 D5 A2 15 ground pins be connected to the Encoder Oscillator F 70 kHz 4 ENC 11 D6 A1 14 Data Input: ground plane. 12 D7 A0 13 Logic Low 0.0 0.2 x V VDC 4 CC Figure 2: Test / Basic Application Circuit Logic High V x 0.8 V VDC 4 CC CC Input Sink Current 0.6 1.0 1.2 mA 4 ENVIRONMENTAL TYPICAL PERFORMANCE GRAPHS Operating Temperature Range -30 +70 C4 +8 12 With LADJ tied to ground +7 Table 1: KH2 Series Transmitter Electrical Specifications 11 +6 10 +5 9 +4 Notes 8 +3 +2 1. Current draw with 50% mark / space ratio. 7 +1 2. Into a 50 load. 6 With LADJ tied to ground 0 5 3. With 430 resistor on LADJ. -1 4 4. Characterized, but not tested. -2 3 -3 With 430 resistor on LADJ -4 2 -5 1 With 430 resistor on LADJ -6 0 -7 2.5 5.0 3.0 3.5 4.0 4.5 2.5 3.0 3.5 4.0 4.5 5.0 Supply Voltage (V) Supply Voltage (V) Figure 3: Supply Current vs. Supply Voltage Figure 4: Output Power vs. Supply Voltage +8 *CAUTION* +7 +6 This product incorporates numerous static-sensitive components. +5 Always wear an ESD wrist strap and observe proper ESD handling +4 procedures when working with this device. Failure to observe this +3 5V +2 precaution may result in module damage or failure. +1 0 -1 3V -2 -3 -4 51 100 150 200 240 300 360 430 510 560 620 680 750 820 910 1.1K LADJ Pin Resistor Value () Figure 5: Output Power vs. LADJ Resistor Page 3 Page 2 Supply Current (mA) Output Power (dBm) Output Power Into 50 ohms (dBm)